Dell D03T Скачать руководство пользователя страница 57

Страница: 57 / 119

Steps

1. Loosen the four captive screws that secures the M.2 heat-sink to the system board.
2. Lift and remove the M.2 heat-sink from the computer.
3. Remove the single (M2x3.5) screws that secures the solid-state drive to the system board.

NOTE:

If the computer has two solid-state drives installed, repeat the same steps for the second solid-state drive.

4. Slide and lift the solid-state drive off the system board.

Installing the M.2 2280 PCIe solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the
installation procedure.

Removing and installing components

Содержание D03T
























































































































Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды

Dell D03T, Руководство по обслуживанию

Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды