Dell Broadcom NetXtreme Family of Adapters Скачать руководство пользователя страница 69

Страница: 69 / 224

iSCSI Protocol: Broadcom NetXtreme II Network Adapter User Guide

file:///T|/htdocs/NETWORK/BroadCom/71921/NetXtremeII/en/iscsi.htm[9/26/2012 3:29:03 PM]

following using the values used when configuring the iSCSI target:

IP Address
TCP Port
Boot LUN
iSCSI Name

8. Select

ESC

to return to the

Main

menu.

9. A second iSCSI boot adapter can be configured for redundancy in the event the primary adapter fails to boot. To

configure the secondary device parameters, select

Secondary Device Parameters

from the

Main

menu (see

Configure Parameters for a Secondary Adapter

). Otherwise, go to step 10.

10. Select

ESC

and select

Exit and Save Configuration

11. Select

to save your MBA configuration.

Dynamic iSCSI Boot Configuration

In a dynamic configuration, you only need to specify that the system's IP address and target/initiator information are

provided by a DHCP server (see IPv4 and IPv6 configurations in

Configuring the DHCP Server to Support iSCSI Boot

). For

IPv4, with the exception of the initiator iSCSI name, any settings on the Initiator Parameters, 1st Target Parameters, or 2nd

Target Parameters screens are ignored and do not need to be cleared. For IPv6, with the exception of the CHAP ID and

Secret, any settings on the Initiator Parameters, 1st Target Parameters, or 2nd Target Parameters screens are ignored and do

not need to be cleared. For information on configuration options, see

Table 1

NOTE: When using a DHCP server, the DNS server entries are overwritten by the values provided by the DHCP server.

This occurs even if the locally provided values are valid and the DHCP server provides no DNS server information. When the

DHCP server provides no DNS server information, both the primary and secondary DNS server values are set to 0.0.0.0. When

the Windows OS takes over, the Microsoft iSCSI initiator retrieves the iSCSI Initiator parameters and configures the

appropriate registries statically. It will overwrite whatever is configured. Since the DHCP daemon runs in the Windows

environment as a user process, all TCP/IP parameters have to be statically configured before the stack comes up in the iSCSI

Boot environment.

If DHCP Option 17 is used, the target information is provided by the DHCP server, and the initiator iSCSI name is retrieved

from the value programmed from the Initiator Parameters screen. If no value was selected, then the controller defaults to the

name:

iqn.1995-05.com.broadcom.<11.22.33.44.55.66>.iscsiboot

where the string

11.22.33.44.55.66

corresponds to the controller's MAC address.

If DHCP option 43 (IPv4 only) is used, then any settings on the Initiator Parameters, 1st Target Parameters, or 2nd Target

Parameters screens are ignored and do not need to be cleared.

To configure the iSCSI boot parameters using dynamic configuration

1. From the

General Parameters Menu

screen, set the following:

TCP/IP parameters via DHCP

: Enabled. (For IPv4.)

IP Autoconfiguration

: Enabled. (For IPv6, non-offload.)

iSCSI parameters via DHCP

: Enabled

CHAP Authentication

: Disabled

Boot to iSCSI target

: Disabled

DHCP Vendor ID

: BRCM ISAN

Link Up Delay Time

: 0

Use TCP Timestamp

: Enabled (for some targets such as the Dell/EMC AX100i, it is necessary to enable

Use

TCP Timestamp)
Target as First HDD

: Disabled

LUN Busy Retry Count

: 0

IP Version

: IPv6. (For IPv6, non-offload.)

HBA Boot Mode

: Disabled

2. Select

ESC

to return to the

Main

menu.

Содержание Broadcom NetXtreme Family of Adapters

































































































































































































































Результаты поиска

Содержание Broadcom NetXtreme Family of Adapters

Отзывы:

Похожие инструкции для Broadcom NetXtreme Family of Adapters

Бренды по названию

Популярные бренды

Dell Broadcom NetXtreme Family of Adapters, Руководство пользователя

Результаты поиска

Содержание Broadcom NetXtreme Family of Adapters

Отзывы:

Похожие инструкции для Broadcom NetXtreme Family of Adapters

Бренды по названию

Популярные бренды