Using Broadcom Advanced Control Suite 4: Broadcom NetXtreme II Network Adapter User Guide
file:///T|/htdocs/NETWORK/BroadCom/71921/NetXtremeII/en/bacs.htm[9/26/2012 3:29:48 PM]
1. Click the name of the Broadcom NetXtreme II iSCSI device in the SCSI controller section of the Explorer View pane.
2. Depending on the protocol you will be using, for
IPv4 DHCP
or
IPv6 DHCP
, select
Enable
(not available for iSCSI booted
adapters) to set the IP address dynamically using a DHCP server. Or select
Disable
to set the IP address using a static IP
address. Enter the
IP Address
,
Subnet Mask
, and
Default Gateway
.
3. Configure the VLAN ID for the iSCSI HBA by entering a number for
VLAN ID
. The value must be between 0 and 4094.
4. After the configurations are complete, click
Apply
to save the settings or click
Reset
to revert back to the previous settings.
Viewing Licenses
NOTES:
The
Licenses
section of the
Configurations
tab is only available for Broadcom NetXtreme II adapters and VBD drivers.
Not all offload technologies are available with all adapters.
The
Licenses
section shows the number of connections available for TOE and iSCSI offload technologies.
To view licenses
1. Click the name of the Broadcom NetXtreme II system device in the Explorer View pane.
Configuring Teaming
The teaming function allows you to group any available network adapters together to function as a team. Teaming is a method of
creating a virtual NIC (a group of multiple adapters that functions as a single adapter). The benefit of this approach is that it enables
load balancing and failover. Teaming is done through the Broadcom Advanced Server Program (BASP) software. For a comprehensive
description of the technology and implementation considerations of the teaming software, refer to the "Broadcom Gigabit Ethernet
Teaming Services" section of your Broadcom network adapter user guide.
Teaming can be accomplished by either of the following methods:
Using the Broadcom Teaming Wizard
Using Expert Mode
NOTES:
For further information regarding teaming protocols, see "Teaming" in your Broadcom network adapter user guide.
If you do not enable LiveLink™ when configuring teams, disabling Spanning Tree Protocol (STP) at the switch is
recommended. This minimizes the downtime due to spanning tree loop determination when failing over. LiveLink
mitigates such issues.
BASP is available only if a system has one or more Broadcom network adapters installed.
The TCP Offload Engine (TOE), Large Send Offload (LSO), and Checksum Offload properties are enabled for a team only
when all of the members support and are configured for the feature.
If an adapter is included as a member of a team and you change any advanced property, then you must rebuild the
team to ensure that the team's advanced properties are properly set.
If an adapter with a TOE key is included as a member of a team and you remove the TOE key, then you must rebuild
the team to ensure that the team does not appear as a TOE-enabled team.
You must have administrator privileges to create or modify a team.
The load balance algorithm in a team environment in which members are connected at different speeds favors members
connected with a Gigabit Ethernet link over members connected at lower speed links (100 Mbps or 10 Mbps) until a
threshold is met. This is normal behavior.
In a GEC or 802.3ad type team, disabling the device driver(s) of a team member that has IPMI enabled may prevent a
successful failover since IPMI maintains link with the attached switch.
Do not assign a Locally Administered Address on any physical adapter that is a member of a team.
Team Types
You can create four types of load balance teams:
Smart Load Balance and Failover
Link Aggregation (802.3ad) (TOE is not applicable)
Generic Trunking (FEC/GEC)/802.3ad-Draft Static (TOE is not applicable)
