Dell 2145 Color Laser Скачать руководство пользователя

Страница: 76 / 141

Troubleshooting

Color or Black

background

If the amount of background shading becomes

unacceptable:

•

Change to a lighter weight paper. See

"Selecting print media" on page 24.

•

Check the printer’s environment: very dry

(low humidity) or high humidity (higher than

80% RH) conditions can increase the

amount of background shading.

•

Remove the old toner cartridge and install

a new one. See "Replacing the toner

cartridge" on page 59.

Toner smear

•

Clean the inside of the printer. See

"Cleaning the inside" on page 56.

•

Check the paper type and quality. See

"Selecting print media" on page 24.

•

Remove the toner cartridge and install a

new one. See "Replacing the toner

cartridge" on page 59.

Vertical repetitive

defects

If marks repeatedly appear on the printed side

of the page at even intervals:

•

The toner cartridge may be damaged. If a

repetitive mark occurs on the page, print a

cleaning sheet several times to clean the

cartridge. After the printout, if you still have

the same problems, remove the toner

cartridge and install a new one. See

"Replacing the toner cartridge" on page 59.

•

Parts of the printer may have toner on

them. If the defects occur on the back of

the page, the problem will likely correct

itself after a few more pages.

•

The fusing assembly may be damaged.

Contact a service representative.

Background scatter

Background scatter results from bits of toner

randomly distributed on the printed page.

•

The paper may be too damp. Try printing

with a different batch of paper. Do not open

packages of paper until necessary so that

the paper does not absorb too much

moisture.

•

If background scatter occurs on an

envelope, change the printing layout to

avoid printing over areas that have

overlapping seams on the reverse side.

Printing on seams can cause problems.

•

If background scatter covers the entire

surface area of a printed page, adjust the

print resolution through your software

application or the printer properties.

CONDITION

SUGGESTED SOLUTIONS

Misformed

characters

•

If characters are improperly formed and

producing hollow images, the paper stock

may be too slick. Try a different paper. See

"Selecting print media" on page 24.

•

If characters are improperly formed and

producing a wavy effect, the scanner unit

may need service. For service, contact a

service representative.

Page skew

•

Ensure that the paper is loaded properly.

•

Check the paper type and quality. See

"Selecting print media" on page 24.

•

Ensure that the paper or other material is

loaded correctly and the guides are not too

tight or too loose against the paper stack.

Curl or wave

•

Ensure that the paper is loaded properly.

•

Check the paper type and quality. Both high

temperature and humidity can cause paper

curl. See "Selecting print media" on

page 24.

•

Turn over the stack of paper in the tray. Also

try rotating the paper 180° in the tray.

Wrinkles or creases

•

Ensure that the paper is loaded properly.

•

Check the paper type and quality. See

"Selecting print media" on page 24.

•

Turn over the stack of paper in the tray. Also

try rotating the paper 180° in the tray.

Back of printouts

are dirty

•

Check for leaking toner. Clean the inside of

the printer. See "Cleaning the inside" on

page 56.

CONDITION

SUGGESTED SOLUTIONS

AaBbCc

Содержание 2145 Color Laser














































































































































Результаты поиска

Содержание 2145 Color Laser

Отзывы:

Похожие инструкции для 2145 Color Laser

Бренды по названию

Популярные бренды

Dell 2145 Color Laser, Руководство пользователя

Результаты поиска

Содержание 2145 Color Laser

Отзывы:

Похожие инструкции для 2145 Color Laser

Бренды по названию

Популярные бренды