Dell 2145 Color Laser Скачать руководство пользователя

Страница: 70 / 141

Troubleshooting

UNDERSTANDING DISPLAY MESSAGES

Messages appear on the control panel display to indicate the printer’s status

or errors. Refer to the tables below to understand the messages’ meaning

and correct the problem if necessary. Messages and their meanings are

listed in alphabetical order.

•

If the message is not in the table, cycle the power and try the

printing job again. If the problem persists, call for service.

•

Some messages may not appear in the display depending on

options or models.

•

xxx indicates the media type.

•

yyy indicates the tray.

MESSAGE

MEANING

SUGGESTED

SOLUTIONS

[COMM. Error]

The printer has a

communication

problem.

Ask the sender to try

again.

[Incompatible]

The printer has

received a fax from

which is registered as

a junk fax.

The received fax data

will be deleted.

Reconfirm junk fax

setup. See "Receiving

options" on page 48

[Line Error]

Your printer cannot

connect with the

receiving fax printer or

has lost contact

because of a problem

with the phone line.

Try again. If the problem

persists, wait an hour or

so for the line to clear

and try again.

Or, turn the ECM mode

on. See "Sending

options" on page 48

[No Answer]

The receiving fax

printer has not

answered after

several redial

attempts.

Try again. Ensure that

the receiving printer is

operational.

[Stop Pressed]

Stop/Clear

(

)

has

been pressed during

an operation.

Try again.

[yyy]

Paper Empty

There is no paper in

the tray.

Load paper in the tray.

[yyy]

Paper Mismatch

The paper size

specified in the printer

properties does not

match the paper you

are loading.

Load the correct paper in

the tray.

[yyy]

Cassette Out

The tray cassette is

not properly closed.

To close the tray, lower

the rear edge, align it

with the slot, and slide it

into the printer.

Adjusting...

Registration

The printer is

adjusting the color

registration.

Wait a few minutes.

Authentication

Failure

The ID or password

you entered is

incorrect.

Enter the correct ID or

password.

Cancel?

Yes

Your printer’s memory

has become full while

trying to store an

original into memory.

To cancel the fax job,

press the

button to

Yes

If you want to send those

pages that have been

successfully stored,

press the

button to

. You should

send the remaining

pages later, when

memory is available.

Connection Error

Connection with the

SMTP server failed.

Check the server

settings and the network

cable.

Connection Failed

The protocol you have

entered is not

supported or server

port is wrong.

Check the protocol or

server port.

DADF Cover

Open Error

The DADF cover is

not securely latched.

Close the DADF cover

until it locks into place.

Data Read Fail

Check USB Mem.

Time expired while

reading data.

Try again.

Data Write Fail

Check USB Mem.

Storing to the USB

memory failed.

Check the available USB

memory space.

Document Jam

The loaded original

has jammed in the

DADF.

Clear the jam (see

"Clearing document

jams" on page 63).

Door Open/Check

Transfer Belt

The front cover is not

securely latched.

Close the cover until it

locks into place.

Duplex Jam 0

Check Inside

Paper has jammed

during duplex printing.

This is applicable only

to printers with this

feature.

Clear the jam

(see "Clearing paper

jams" on page 64).

Duplex Jam 1

Open/Close Door

Paper has jammed

during duplex printing.

This is applicable only

to printers with this

feature.

Clear the jam

(see "Clearing paper

jams" on page 64).

Enter Again

You entered an

unavailable item.

Enter the correct item

again.

File Access

Denied

server was

successful. However,

access to the file on

the network server

was denied.

Change the server

settings.

File Format

Not Supported

The selected file

format is not

supported.

Use the correct file

format.

MESSAGE

MEANING

SUGGESTED

SOLUTIONS

Содержание 2145 Color Laser














































































































































Результаты поиска

Содержание 2145 Color Laser

Отзывы:

Похожие инструкции для 2145 Color Laser

Бренды по названию

Популярные бренды

Dell 2145 Color Laser, Руководство пользователя

Результаты поиска

Содержание 2145 Color Laser

Отзывы:

Похожие инструкции для 2145 Color Laser

Бренды по названию

Популярные бренды