Delios DLS 300 Скачать руководство пользователя

Страница: 49 / 64

DLS 300 / 450 / 600

Code 240.010.0001

•

“LITHIUM ” Menu

By accessing the “LITHIUM” menu, the Lithium battery type, make and model can be selected amongst

those supported by the DLS system.

By selecting a Lithium battery, the DLS system can be configured to interact only with the selected battery

type, make and model.

The Lithium battery configuration settings can be used only by qualified staff. Changing the settings by

unqualified staff could affect the correct operation of the system and relieves the manufacturer from all li

abilities, as well as invalidate the warranty.

Some additional settings can be accessed only in the INSTALLER mode, which requires a password to be

entered (see the section “LOGIN Menu”).

Parameters at installer level can only be accessed by qualified staff. Changing the installer level param

eters by unqualified staff could affect the correct operation of the system and relieves the manufacturer from

all liabilities, and invalidates the warranty.

6.6.5 “HOME AUTOMATION” Menu

Access the “HOME AUTOMATION” menu to set up the HOME AUTOMATION PCB (optional).

The references related to the independent programmable contacts on the HOME AUTOMATION PCB are:

LD1

→ Enable/disable LD1 relay

LD2

→ Enable/disable LD1 relay

LD3

→ Enable/disable LD1 relay

LD4

→ Enable/disable LD1 relay

GEN

→ Enable/disable GEN relay

AUX

→ Enable/disable AUX relay

The

LD1 ÷ LD4

and therefore the loads applied to the associated contacts are enabled by configuring the

following parameters, specific for each load:

•

LD ON/OFF

→ Select ON to enable the contact control. Select OFF to disable the contact control.

• P START

→ Select the threshold for the power coming from the PV generator, above which the contact

is enabled. The contact is enabled when the available power from the PV array is higher than the set

threshold. The contact is disabled when the available power from the PV array is lower than the set

threshold.

• START LD DAY

→ Select the days of the week when the contact is enabled to operate.

• START LD H

→ Select the time starting from which the contact is enabled to operate.

• STOP LD H

→ Select the time starting from which the contact is disabled to operate.

The GEN contact is activated to remotely control the auxiliary power generator and occurs according to the

following modes:

• GEN

→

The contact is activated when the system detects that at the same time the grid power is

unavailable and the battery is flat. The contact is disabled when one of the two statuses is restored.

With contact GEN enabled, the energy produced by the PV generator is used by the system to restore

the battery charge status.

The AUX contact is dedicated to remotely signal or monitor the external devices when an alarm condition

is detected by the system and is carried as shown below:

• AUX

→ The contact is enabled when the system detects a general alarm condition. The contact is

disabled when the alarm condition is removed.

Содержание DLS 300

































































Результаты поиска

Содержание DLS 300

Отзывы:

Похожие инструкции для DLS 300

Бренды по названию

Популярные бренды

Delios DLS 300, Инструкция по эксплуатации

Результаты поиска

Содержание DLS 300

Отзывы:

Похожие инструкции для DLS 300

Бренды по названию

Популярные бренды