manualshive.com logo in svg

Delem DAC-360, Руководство по установке, Страница: 75 / 82

Поделиться
Скачать
Delem DAC-360 Скачать руководство пользователя страница 75

Delem

V0208, 2.49

4.4.

Display codes

In the upper richt corner of the screen, a status code is shown that indicates the current status 
of the control. Such a code can either be a status code or and error code.

The following table shows the possible status codes:

The following table shows the possible error codes:

(1) If this error occurs, reboot the control. If the error persists, contact your machine supplier.

S0

Stopped

Waiting for the operator to press start while pump start is 
high

S1

Positioning

Not all axes are in position yet

S2

Wait for ST low

Waiting for STEP input falling edge

S3

Wait for EOS

Wait for EOS, generated by potentiometer or BR

S4

Wait for UDP

Wait for UDP, generated by potentiometer or STEP input

S5

Wait for STEP high

Waiting for STEP input rising edge

S6

Wait for end of retract Waiting for end of retract when STEP is already high.

S7

Wait for safe X

Waiting until X-axis is in safe area

E1..

Internal error (1)

E21

Power supply failure

E23

Encoder 1 error

E24

Encoder 2 error

E53

Invalid parameters

E56

No movement on X-axis

E57

No movement on A-axis

E58

No movement on G1-axis

E59

No movement on G2-axis

E94

Internal error (1)

Содержание DAC-360



















































































Отзывы:

Нет отзывов