Delem DAC-360 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 82

Delem DAC-360 Скачать руководство пользователя страница 61

Delem

V0208, 2.35

Due to the inertia of the system it is possible that the shear has a slight overshoot when it is
stopped at the computed value. The programmed ‘prestop’-value is subtracted from the
computed value, creating an EOS (end of stroke) output signal at an earlier moment than the
programmed moment.

2.6.

Force control parameters

Parameter 93

Main force enable

Range

: 0 - 1

Unit

: -

Default

: 0

Function

Enable or disable cutting force on the control.
0 = no control
1 = cutting force control enabled

Parameter 94

Cutting force factor

Range

: 0.1 - 999.9

Unit

: -

Default

: 1.0

Function

The (initially) calculated cutting force is multiplied with this factor.

Parameter 95

Main force reference table

Range

: -

Unit

: -

Default

: -

Function

Press ENTER to open a screen with the Cutting reference table. In this table, the relation
between cutting force and control output voltage can be programmed.

«
...
59
60
61
62
63
...
»

Содержание DAC-360



















































































Отзывы:

Нет отзывов