Delem DAC-360 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 82

Delem DAC-360 Скачать руководство пользователя страница 2

V0208, 0.2

PREFACE

In this installation manual you find information how to connect and program a DAC-360 shear
control for operation with an industrial shear.

LIMITED WARRANTY

•

The equipment is supplied by Delem without safety features. The machine manufacturer
has to ensure a safe environment.

•

This equipment must be installed and used in accordance with Delem's specifications.
The guarantee on the equipment is invalidated in the event of improper installation and/
or use of this equipment.

•

The General Terms and Conditions of Delivery of Delem shall apply to this product.
These conditions are available from Delem on request.

•

This manual does not entitle you to any rights. Delem reserves the right to change this
manual without prior warning.

•

All rights reserved. The copyright is held by Delem. No part of this publication may be
copied or reproduced without written permission from Delem BV.

«
1
2
3
4
...
»

Содержание DAC-360



















































































Отзывы:

Нет отзывов