Delem DAC-360 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 82

Delem DAC-360 Скачать руководство пользователя страница 53

Delem

V0208, 2.27

The value is programmed in AD-points: a converted digital value of the position feedback
voltage of the potentiometer.

Parameter 73

Angle prestop negative

Range

: 0 - 99

Unit

: AD value

Default

: 0

Function

This parameter has the same definition as parameter "Angle Prestop Positive" but only in the
negative direction of the angle adjustment (smaller angle).

Parameter 74

Angle reference table

Range

: -

Unit

: -

Default

: -

Function

Press ENTER to open the screen with the angle reference table. In this table, the relation
between the blade angle and the feedback voltage can be programmed.

Angle: program a known angle value for the blade.
AD-value: program the required feedback voltage for this angle. The feedback voltage must
be programmed in the range 0-4095, which represents the input voltage in the range 0-10V.
Use the diagnostic mode to find the correct AD-values. Move the blade to and angle, measure
the angle position and notice the corresponding AD-value from the analog input.

Parameter 75

Angle material table

Range

: -

«
...
51
52
53
54
55
...
»

Содержание DAC-360



















































































Отзывы:

Нет отзывов