Deif AGC-4 Mk II Скачать руководство пользователя страница 33

Страница: 33 / 50

5. List of outputs

5.1

Commands

5.1.1

Genset controller commands

Output, Command

Description

Notes

Lamp test

Activate lamp test (LEDs on display).

Ack. all alarms

Acknowledge all alarms.

Set clock to 4 am

Set the controller clock to 04h00.

Derate Pnom [1-3]

Activate nominal power derate.

Select test type to simple

Test sequence selection.

Select test type to load

Test sequence selection.

Select test type to full

Test sequence selection.

Freeze ramp

Locks the power ramp up function until the command is disabled again.

Idle run low speed

Idle speed constant low speed.

Idle run temp control

Idle speed temperature-dependent.

Cool down threshold

Interrupt cool down sequence.

Inductive reference

Inductive cos phi reference.

Capacitive reference

Capacitive cos phi reference.

Act. dynamic sync.

Activate dynamic sync.

Act. static sync.

Activate static sync.

Fan A running

Running feedback for cooling fan A.

Fan B running

Running feedback for cooling fan B.

Fan C running

Running feedback for cooling fan C.

Fan D running

Running feedback for cooling fan D.

Act. power offset [1-3]

Activate the power reference offset.

Deact. power offset [1-3]

Deactivate the power reference offset.

Act. cos phi offset [1-3]

Activate cos phi reference offset.

Deact. cos phi offset [1-3]

Deactivate cos phi reference offset.

Activate Fuel Pump

Override fuel pump hysteresis to fill the tank to threshold level.

Reset horn

Reset the horn relay.

Reset I max. demand

Reset the peak current detected in the controller.

Reset I thermal demand

Reset the thermal current detected in the controller.

Pulse counter [1-2]

Increase the selected pulse counter.

Reset pulse counter [1-2]

Reset the selected pulse counter.

Force use of analogue offset [1-4]

This command forces the selected analogue offset to be active.

Mains sync. inhibit activate

Activates the close inhibit functionality on the mains breaker.

Mains sync. inhibit deactivate

Deactivates the close inhibit functionality on the mains breaker.

Ack. mains protection alarms

Acknowledges all mains alarms including: 1270-1430, 1660, 1700, 1960, 1970,
7480-7490.

Application note 4189341276B EN

Page 33 of 50

Содержание AGC-4 Mk II



















































Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Похожие инструкции для AGC-4 Mk II

Бренды по названию

Популярные бренды

Deif AGC-4 Mk II, Руководство пользователя

Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Похожие инструкции для AGC-4 Mk II

Бренды по названию

Популярные бренды