Deif AGC-4 Mk II Скачать руководство пользователя страница 39

Страница: 39 / 50

Description

Notes

Select application [1-4]

Power management: Select the application from the controller.

Open BTB

Open the bus tie breaker.

Close BTB

Close the bus tie breaker.

Select three phase system

Sets the controller to work in a three-phase system.

Select split L1L3 phase system

Sets the controller to work in a two-phase system (L1-L3).

Select split L1L2 phase system

Sets the controller to work in a two-phase system (L1-L3).

Select single phase system

Sets the controller to work in a single-phase system (L1).

Reset horn

Reset the horn relay.

Reset I max. demand

Reset the peak current detected in the controller.

Reset I thermal demand

Reset the thermal current detected in the controller.

Pulse counter [1-2]

Increase the selected pulse counter.

Reset pulse counter [1-2]

Reset the selected pulse counter.

Set parameter [1-2]

Select the parameter set for nominal settings.

Ack. BB protection alarms

Acknowledges all busbar alarms including: 1270-1430, 1660, 1700, 1960, 1970,
7480-7490.

Access lock

Activates access lock.

Direct close on dead BA and dead BB

See

Special M-Logic function - BTB direct close

Option G5 Power

management

Direct close breaker on dead BA or dead BB

See

Special M-Logic function - BTB direct close

Option G5 Power

management

Breaker configuration: Normal Close

See

Tie breaker configuration

Option G5 Power management

Breaker configuration: Normal Open

See

Tie breaker configuration

Option G5 Power management

Assume all BTB POS fdb OFF in case of pos
fail or ID missing

Fault handling procedure.

More information

See

Option G5 Power management

for information about BTB commands.

5.1.4

Group tie breaker controller commands

Commands for group tie breaker

Description

Notes

Island

Island function mode.

AMF

AMF (Automatic Mains Failure) function mode.

Peak shaving

Peak shaving function mode.

Fixed power

Fixed power function mode.

Mains power export

Mains power export function mode.

Load take over

Load take over function mode.

Genset group

Semi-Auto mode

Semi-auto running mode.

Test mode

Test running mode.

Auto mode

Auto running mode.

Application note 4189341276B EN

Page 39 of 50

Содержание AGC-4 Mk II



















































Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Похожие инструкции для AGC-4 Mk II

Бренды по названию

Популярные бренды

Deif AGC-4 Mk II, Руководство пользователя

Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Похожие инструкции для AGC-4 Mk II

Бренды по названию

Популярные бренды