Deif AGC-4 Mk II Скачать руководство пользователя страница 2

Страница: 2 / 50

................................................................................................................................................................................................

1.1.1 General purpose

.................................................................................................................................................................................................................

1.1.2 Intended users

1.2 Warnings, safety and legal information

.........................................................................................................................................................................

1.2.1 Symbols for hazard statements

....................................................................................................................................................................................

1.2.2 Symbols for general notes

..............................................................................................................................................................................................

1.2.3 Safety during installation and operation

...................................................................................................................................................................

1.2.4 Factory settings

1.2.5 Legal information and disclaimer

.................................................................................................................................................................................

2. General description

2.1 Introduction

2.1.1 Introduction to M-Logic

....................................................................................................................................................................................................

3. Configuration

3.1 Starting

3.1.1 Starting the M-Logic

3.1.2 Read/write

3.1.3 Save/open

3.2 Basic functions

3.2.1 Basic functions

3.2.2 Event settings

3.2.3 Operators

3.2.4 Enable this rule

3.2.5 Output settings

3.3 Definitions

3.4 Examples

3.4.1 Virtual events

3.4.2 Set/reset function

3.4.3 Configure an AOP LED

.................................................................................................................................................................................................

3.4.4 Controlling a relay output with a single AOP button

.........................................................................................................................................

3.4.5 Power up in a specific mode

.......................................................................................................................................................................................

3.4.6 Flip flop function

4. List of events

4.3.1 Genset controller events

...............................................................................................................................................................................................

4.3.2 Mains controller events

.................................................................................................................................................................................................

4.3.3 Bus tie breaker controller events

..............................................................................................................................................................................

4.3.4 Group tie breaker controller events

..........................................................................................................................................................................

4.3.5 Plant controller events

...................................................................................................................................................................................................

4.4 Close before excitation (CBE)

..........................................................................................................................................................................................

4.5 Redundancy events

Application note 4189341276B EN

Page 2 of 50

Содержание AGC-4 Mk II



















































Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Бренды по названию

Популярные бренды

Deif AGC-4 Mk II, Руководство пользователя

Результаты поиска

Содержание AGC-4 Mk II

Отзывы:

Бренды по названию

Популярные бренды