DeDietrich IX 145-110 Скачать руководство пользователя страница 106

Страница: 106 / 132

6. Check the L2 distance between the ignition electrode and the burner.

Tab.79 Ignition electrode and burner

Boiler

L2 distance

IX 145–50

IX 145–70

IX 145–90

10 mm / tolerance of +/- 1 mm

IX 145–110

7.5 mm / tolerance of +/- 1 mm

Important

Replace the ignition electrode if it is damaged.

7. Check the L3 distance between the ignition electrode and the ground

electrode.

Tab.80 Ignition electrode and ground electrode

Boiler

L3 distance

IX 145–50

IX 145–70

IX 145–90

IX 145–110

4 mm / tolerance of +/- 0.5 mm

Important

Replace the ignition electrode if it is damaged.

8. Check whether the insulation on the inside surface of the burner is

damaged in any way. The surface must be clean and free of any

damage. Replace the insulation if it is damaged.

9. Remount the burner.

For more information, see

Removing the burner, page 103

Remounting the burner, page 107

11.2.5 Cleaning the siphon

1. Remove the burner.

2. Access the siphon.

3. Disconnect the pipe coming from the combustion chamber (IX 145–50

and IX 145–70 only).

4. Disconnect the pipe from the flue gas exchanger.

5. Disconnect the condensates discharge pipe.

Important

Use a pair of pliers to remove the spring tightening clamps.

6. Remove the siphon from the heating body by taking out the retaining

screw with a cross-head screwdriver.

7. Clean the bottom of the siphon with water.

8. Completely fill the siphon.

Danger

Fill the siphon to the top. If the siphon is empty, there is a danger

of poisoning by combustion products.

9. Put the siphon back on the heating body and put the retaining screw

back in place with a cross-head screwdriver.

10. Reconnect the pipe from the combustion chamber, the pipe from the

flue gas exchanger and, finally, the condensates discharge pipe.

Important

Use a pair of pliers to put the spring tightening clamps back in

place.

Fig.123

-3

Fig.124

-3

-0

Fig.125

-3

-2

11 Maintenance

106

7702703 - v04 - 05092019

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды