manualshive.com logo in svg

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Поделиться
Скачать
DeDietrich IX 145-110 Скачать руководство пользователя страница 111

Display

Description of the er­

ror

Probable causes

Check/Solution

40

40:Return sensor 1

NTC return sensor

The return sensor is not correctly 

connected

Check that the return sensor has 

been correctly connected to the 

boiler PCB

The return sensor does not work

Use a suitable multimeter to check 

the resistance (Ω) of the sensor ac­

cording to the water temperature 

using the "Resistance/Tempera­

ture" correspondence table (10 K 

sensor)

46

46:Return sensor 

cascade

Cascade return tem­

perature sensor error

The return sensor is not correctly 

connected

Check that the return sensor has 

been correctly connected to the 

boiler PCB

The return sensor does not work

Use a suitable multimeter to check 

the resistance (Ω) of the sensor ac­

cording to the water temperature 

using the "Resistance/Tempera­

ture" correspondence table (10 K 

sensor)

50

50:HW sensor 1

DHW sensor

The sensor is not correctly connec­

ted to the boiler sensor terminal 

block

Check that the sensor has been 

correctly connected to the boiler 

sensor terminal block

The DHW temperature sensor does 

not work

Use a suitable multimeter to check 

the resistance (Ω) of the sensor ac­

cording to the room temperature 

using the "Resistance/Tempera­

ture" correspondence table (10 K 

sensor)

52

52:HW sensor 2

Solar DHW sensor (if 

incorporating a solar 

installation)

The sensor is not correctly connec­

ted to the boiler sensor terminal 

block

Check that the sensor has been 

correctly connected to the boiler 

sensor terminal block.

The return temperature sensor does 

not work

Use a suitable multimeter to check 

the resistance (Ω) of the sensor ac­

cording to the room temperature 

using the "Resistance/Tempera­

ture" correspondence table 

(PT 1000 sensor)

60

60:Room sensor 1

Room temperature 

sensor 1 error

The sensor is not correctly connec­

ted to the boiler sensor terminal 

block

Check that the room sensor has 

been correctly connected to the 

boiler sensor terminal block

65

65:Room sensor 2

Room temperature 

sensor 2 error

The sensor is not correctly connec­

ted to the boiler sensor terminal 

block

Check that the room sensor has 

been correctly connected to the 

boiler sensor terminal block

68

68:Room sensor 3

Room temperature 

sensor 3 error

The sensor is not correctly connec­

ted to the boiler sensor terminal 

block

Check that the room sensor has 

been correctly connected to the 

boiler sensor terminal block

78

78:Water pressure 

sensor

Hydraulic pressure 

sensor error

The hydraulic pressure sensor is 

not connected to the PCB

Check that the connectors between 

the sensor and the PCB are cor­

rectly connected

The hydraulic pressure sensor does 

not work

Replace the hydraulic pressure 

sensor. Please note that this action 

requires the boiler to be drained

73

73:Collector sensor 1

Solar collector sensor 

(if incorporating a so­

lar installation)

The sensor is not correctly connec­

ted to the boiler sensor terminal 

block

Check that the sensor has been 

correctly connected to the boiler 

sensor terminal block

The solar collector sensor does not 

work

Use a suitable multimeter to check 

the resistance (Ω) of the sensor ac­

cording to the room temperature 

using the "Resistance/Tempera­

ture" correspondence table 

(PT 1000 sensor)

12 Troubleshooting

7702703 - v04 - 05092019

IX

111

Содержание IX 145-110





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды