DeDietrich IX 145-110 Скачать руководство пользователя страница 68

Страница: 68 / 132

Unit

at maximum power

(1)

Authorised CO

range at minimum power

(1)

9.8

9.1 - 9.5

9.9

9.2 - 9.6

10.0

(2)

9.3 - 9.7

10.1

9.4 - 9.8

10.2

9.5 - 9.9

10.3

9.6 - 10.0

10.4

9.7 - 10.1

10.5

9.8 - 10.2

(1) The CO

value is valid with the front panel mounted. If the front panel is removed (open chamber), the value readout is lower by 0.2 %.

(2) Nominal value.

Important

The amount of CO

permitted at minimum power depends on the

amount of CO

measured at maximum power. In accordance with

the new standard EN15502 for gas boilers, the settings ranges for

at minimum power are indicated for each CO

value

measured at maximum power.

8.4.6

Adapting the boiler to a different type of gas

Caution

Only a fully trained, qualified professional may carry out the

following operations.

The boiler is pre-set in the factory to run on natural gas H (G20).
Conversion kits are available for other types of gas G25 and G31.

1. Close the mains gas valve.

2. Remove the pipe connecting the Venturi to the gas valve.

Tab.47 Connection pipe

Reference

Model

IX 145–50

IX 145–70

IX 145–90

IX 145–110

3. Remove the Venturi unit.

4. Replace the original Venturi unit with the Venturi unit provided in the

conversion kit.

Fig.68

-3

-0

Fig.69

Removing the Venturi unit

-3

-0

8 Commissioning

7702703 - v04 - 05092019

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды