DeDietrich IX 145-110 Скачать руководство пользователя страница 45

Страница: 45 / 132

6. Remove the detachable panel if necessary.

See

The disassembly instructions can be found on the detachable

panel.

7.3

Hydraulic connections

7.3.1

Connection of the heating circuit

Abide by the mountings shown in the hydraulic diagrams.

Caution

The heating pipe must be mounted in accordance with the

provisions applicable.

If installing stop valves, position the fill/drain valve and the

expansion vessel between the stop valves and the boiler.

Always install a safety valve calibrated to 4 bar on the heating

circuit. The safety valve can be connected to a venting pot. The

safety valve must not be used to drain the heating circuit.

See

If using a hydraulic kit (low-loss header, plate heat exchanger,

cascade kit), use the assembly instructions for the kit.

Important

The pipes are not provided.

1. Remove the anti-dust plug located on the boiler's "heating flow" outlet.

2. Connect the "heating circuit flow" pipe to the "heating flow" outlet on

the boiler.

Fig.43

MW-3000026-02

Fig.44

-3

7 Installation

7702703 - v04 - 05092019

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды