DeDietrich IX 145-110 Скачать руководство пользователя страница 40

Страница: 40 / 132

Important

Relay the pumps if the current exceeds 1 A max. per output.

6.3.3

Connecting boilers in cascade with a OCI 345 module

Connect the boilers included in the boiler cascade with OCI 345 modules

(electronic devices that handle communication through a BUS link). The

OCI 345 modules must be connected to each boiler with three connectors.

Tab.17 Connecting the boiler components in cascade

Component 1

Component 2

OCI 345 module on the boiler

X30 connector on the boiler PCB. (Flat cable supplied with the

OCI 345 module)

MB connector of a OCI 345 module

MB connector of a boiler OCI 345 module

DB connector of a OCI 345 module

DB connector of a boiler OCI 345 module

To make the connections between the various MB and DB connectors,

use a shielded cable with the following specifications:

Type

Cross section

Maximum length

HAR H05 VV-F

2 x 1.5 mm

200 m

6.3.4

Configuration for 1 master boiler and 1 slave boiler

1. Go to the installer parameters on boiler 1 (master boiler).

2. Set the following parameters on boiler 1:

Tab.18 Settings on boiler 1 (master boiler)

Parameter number

Parameter

Adjustment required

5710

Temps / mode CH1

5715

Temps / mode CH2

5721

Temps / mode CH3

Off

5730

Hot water sensor

Hot water sensor B3

5731

Sensor input BX2

Common flow sensor B10

5890

Relay output QX1

heating pump CH1 Q2

5892

Relay output QX3

Hot water ctrl elem Q3

5932

Sensor input BX3

Cascade return sensor B70

6020

Function extension module 1

Temps / mode CH2

6600

Device address

6640

Clock mode

Master

3. Go to the installer parameters on boiler 2 (slave boiler).

Fig.36

Connecting OCI 345 modules for

boilers in cascade

MW-3000042-2

DB.MB

6 Connecting diagrams and configuration

7702703 - v04 - 05092019

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды