DeDietrich IX 145-110 Скачать руководство пользователя страница 107

Страница: 107 / 132

11. Remount the burner.

For more information, see

Removing the burner, page 103

Accessing the internal boiler components, page 43

Remounting the burner, page 107

11.2.6 Remounting the burner

1. Remount the pipe connecting the gas valve to the Venturi unit.

2. Remount the burner, the Venturi and the fan.

Important

Do not forget to remount the igniter on the burner.

Caution

Respect the torque on the burner fastening nuts: 5 N.m +/- 0.5.

Caution

Always use a new tightness gasket to reconnect the gas supply.

3. Reconnect the ignition electrode, the safety thermostat on the

combustion chamber door and the flame detection sensor.

4. Open all valves.

5. Check the tightness of the burner using a leak detection spray.

6. Put the covers back in place on the boiler.

Important

For the IX 145–50 and IX 145–70 models, put the panel located in

front of the burner back in place.

7. Reconnect the earth wire.

8. Re-commission the boiler.

For more information, see

Commissioning procedure, page 59

11.2.7 Thermal fuse in the heat exchanger

The thermal fuse is located in the rear part of the heat exchanger and is

connected in series to the safety thermostat.
The function of the thermal fuse is to ensure the protection of the heat

exchanger against the danger of overheating if the insulation malfunctions.
Intervention by the device is signalled by the on-screen display of the

anomaly 110:Lockout SLT.

1 Rear of the heat exchanger

2 Thermal fuse

Important

When replacing the thermal fuse, also replace the insulating

surface inside the heat exchanger. This insulating surface has

been damaged by overheating.

For more information, see

Removing the burner, page 103

11.2.8 Check the combustion

Checking combustion (maximum heat input)

1. Check the combustion with maximum heat input.

Fig.126

MW-3000214-01

11 Maintenance

7702703 - v04 - 05092019

107

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды