DeDietrich IX 145-110 Скачать руководство пользователя страница 59

Страница: 59 / 132

8 Commissioning

8.1

General

Commissioning the boiler is done for first time use, after a prolonged shut-

down (more than 28 days) or after any event that would require complete

re-installation of the boiler. Commissioning of the boiler allows the user to

review the various settings and checks to be made to start up the boiler in

complete safety.

8.2

Check-list before commissioning

1. Check that the gas type supplied matches the data shown on the

boiler's data plate.

Warning

Do not commission the boiler if the gas supplied does not match

the gas types approved for the boiler.

2. Check connection of the earth wires.

3. Check the tightness of the gas circuit from the non-return valve to the

burner.

4. Check the hydraulic circuit from the boiler's isolation valves to the

connection to the heating body.

5. Check the hydraulic pressure in the heating system.

6. Check the electricity supply connections to the various boiler

components.

7. Check the electrical connections on the thermostat and the other

external components.

8. Check the ventilation in the room in which the system is installed.

9. Check the flue gas connections.

10. Test the boiler at full load.

11. Test the boiler at part load.

For more information, see

Setting the air/gas ratio (maximum heat input), page 61

Setting the air/gas ratio (reduced heat input), page 63

8.3

Commissioning procedure

8.3.1

Checking the gas inlet

Danger

Ensure that the boiler is switched off.

1. Open the main gas valve.

2. Open the gas valve on the boiler.

3. Open the front panel.

4. Check the gas supply pressure at the pressure outlet on the gas valve

unit.

5. Check the tightness of the gas connections made after the gas valve

unit in the boiler.

6. Check the tightness of the gas pipe, including any valves, from the

non-return valve to the burner. The test pressure must not exceed

0.06 bar (0.006 MPa).

7. Vent the gas supply pipe by unscrewing the pressure outlet on the gas

valve unit. Close the outlet again when the pipe has been sufficiently

vented.

8. Check the tightness of the gas connections in the boiler.

For more information, see

Stopping the boiler, page 71

Gas valve basic settings, page 64

8 Commissioning

7702703 - v04 - 05092019

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды