DeDietrich AGC 10/15 Скачать руководство пользователя страница 94

Страница: 94 / 132

Installer level - Menu #NETWORK

(1)

Parameter

Adjustment range Description

Factory setting Customer setting

CASCADE:

: System in cascade

VM NETWORK

(2)

Specific menu: Enlist VMs in cascade

mode (See following chapter:

"Connect VMs only in cascade")

MASTER CONTROLLER

(3)

Configure this control system as

master on the bus

SYSTEM NETWORK

(4)

Specific menu: Enlist generators or

VMs in cascade mode (See following

chapter: "Connecting appliances in

cascade")

FUNCT

(4)

CLASSIC

Operation in cascade: Successive

tripping of the various generators in

the cascade according to needs

CLASSIC

PARALLEL

Functioning in parallel cascade: If the

outside temperature is lower than the

PARALLEL CASC.

value, all

generators are started up at the same

time

PARALLEL CASC.

(5)

-10 to 20 °C

Outside temperature triggering all

stages in parallel mode

10 °C

TIMER GENE P. CASC

(3)

0 to 30 min

Minimum duration of post-operation of

the generator pump

0 mn

INTER STAGE TIMER

(3)

1 to 30 min

Time delay for starting up or shutting

down generators.

4 mn

SLAVE NUMBER

(6)

2 to 10

Set the network address of the

secondary generator

(1) The menu is displayed only if the

INSTALLATION

parameter is set to

EXTENDED

(2) The parameter is only displayed if

CASCADE:

is set to

(3) The parameter is only displayed if

CASCADE:

is set to

(4) The parameter is only displayed if

MASTER CONTROLLER

is set to

(5) The parameter is only displayed if

FUNCT

is set to

PARALLEL

(6) The parameter is only displayed if

MASTER CONTROLLER

is set to

OFF

User level - Menu #SETTING

Parameter Adjustment range Description

Factory setting Customer setting

PERMUT

(1)

AUTO

/ 1 ... 10

This parameter is used to set the master boiler.

AUTO

: The master boiler switches automatically

every 7 days

1 ... 10: The master boiler is always the one

defined by this value

AUTO

(1) The parameter is only displayed if

CASCADE:

is on

and

MASTER CONTROLLER

Connecting appliances in cascade

It is possible, in a cascade configuration, to enlist generators and/or

VM iSystem as slaves. Proceed as follows:
1. Set parameter

CASCADE:

5. Commissioning

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

20/01/2012 - 300026081-001-B

Содержание AGC 10/15





































































































































Результаты поиска

Содержание AGC 10/15

Отзывы:

DeDietrich AGC 10/15, Инструкция по установке и обслуживанию, Страница: 94 / 132

Результаты поиска

Содержание AGC 10/15

Отзывы: