manualshive.com logo in svg

DeDietrich AGC 10/15, Инструкция по установке и обслуживанию, Страница: 30 / 132

Поделиться
Скачать
DeDietrich AGC 10/15 Скачать руководство пользователя страница 30

4. Put the 2 screws in place at the front to attach the boiler to the

DHW tank.

4.4.3.

Positioning the boiler to the left or right of
a DHW tank

1. Put the DHW tank in place.

¼

 Refer to the DHW tank's installation, use and maintenance

instructions.

2. Put the boiler in place.

¼

 See chapter  "Positioning the boiler on its own", page 25

4.4.4.

Reversing the opening direction of the
control panel door

As standard, the control panel access door opens to the left. To open

the control panel access door to the right, proceed as follows:
1. Open and remove the control panel door.

2. Take the control system module out of its housing and disconnect

it.

3. Lift and pivot the control system module support.
4. Remove the control panel.

1

C003099-D

C003121-C

2

3

4

C003122-D

4. Installation

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

28

20/01/2012  - 300026081-001-B

Содержание AGC 10/15





































































































































Отзывы:

Нет отзывов