DeDietrich AGC 10/15 Скачать руководство пользователя страница 69

Страница: 69 / 132

5.2

Check points before commissioning

5.2.1.

Preparing the boiler for commissioning

WARNING

Do not put the boiler into operation if the supplied gas is

not in accordance with the approved gas types.

Preparatory procedure for boiler commissioning:

Check that the gas type supplied matches the data shown on the

boiler's data plate.

Check the gas circuit.

Check the hydraulic circuit.

Check the water pressure in the heating system.

Check the electrical connections to the thermostat and the other

external controls.

Check the other connections.

Test the boiler at full load. Check the setting of the gas/air ratio

and, if necessary, correct it.

Test the boiler at part load. Check the setting of the gas/air ratio

and, if necessary, correct it.

Finalizing work.

5.2.2.

Gas circuit

AGC 10/15 - AGC 15 - AGC 25 - AGC 35

5. Commissioning

20/01/2012 - 300026081-001-B

Содержание AGC 10/15





































































































































Результаты поиска

Содержание AGC 10/15

Отзывы:

DeDietrich AGC 10/15, Инструкция по установке и обслуживанию, Страница: 69 / 132

Результаты поиска

Содержание AGC 10/15

Отзывы: