DDS Calorimeters CAL3K Series Скачать руководство пользователя страница 39

Страница: 39 / 78

DDS CALORIMETERS OPERATIONS MANUAL V1.1

2022

Website:

www.ddscalorimeters.com

Digital Data Systems (Pty) Ltd.

CAL3K Advanced Bomb Calorimeters

www.ddscalorimeters.com

31 MAX MASS LIMIT 0

This limit applies to all possible mass entries. Exceeding this limit prevents a mass from entry. The

default limit is 1.5g

30 MIN MASS LIMIT 0

This limit applies to all possible mass entries. An entry below this limit will be rejected, the default is

0.2g.

21 MISFIRE LIMIT 1

If the sample is not igniting then it is called a misfire. The unit checks the temperature rise 30 seconds

after firing, and if the rise is below the limit a misfire is declared and the process is terminated. The

default value is 0.44C. The misfire limit checking can be disabled by entering zero.

TIME AND DATE

The CAL3K units have a date and time circuit which keeps the time. The data and time are attached to

every calibration, result and event. The following command set the time and date:

4 TIMESET HH:MM:SS 1

This command sets the time in HH:MM:SS. The internal clock runs for about 1 week without power and

then the time (and date) must be set.

5 DATESET YY:MM:DD 1

This sets the date of the CAL3K internal real time clock. Note that the clock remains life up to a week

without power. The entry is the form:

YY/MM/DD

The date can be used as a Group Identification (GID). This is not available on the

CAL3K-S.

122 DATE IS GID 1

This YES/NO entry allows for replacing the GID with the DATE in the form YY/MM/DD. The GID (Group

Identification) is attached to every sample recording. Note that the first 8 characters of the GID are left

blank.

The time can be used as a Sample Identification (SID). This is not available on the

CAL3K-S

. When this

feature is enabled then the auto-increment of the SID is disabled.

121 TIME IS SID 1

Содержание CAL3K Series















































































Результаты поиска

Содержание CAL3K Series

Отзывы:

Похожие инструкции для CAL3K Series

Бренды по названию

Популярные бренды

DDS Calorimeters CAL3K Series, Руководство по эксплуатации

Результаты поиска

Содержание CAL3K Series

Отзывы:

Похожие инструкции для CAL3K Series

Бренды по названию

Популярные бренды