DDC FibreMATRIX FC-76000 Series Скачать руководство пользователя | Manualshive

Страница: 48 / 60

background image

M A N A G E M E N T C O N S O L E

Data Device Corporation

FC-76000 Manual

www.ddc-web.com

Rev A-01/10-0

38

4.2.7.4 Temperature Sub-menu

This screen allows you only one choice: let it auto-refresh every 5 seconds. Press “q”

and then “Enter” to return to the main Statistics menu. This screen displays the

temperature at various points in the switch. The chip temperatures displayed are from

monitor diodes in the FPGA dies, so they are ACTUAL die temperatures. The board

ambient is from a temperature sensor located approximately in the middle of the base

board. This temperature sensor is located to the right of the middle FPGA, when the

switch is held with the front panel on the left and P1/P2 connectors on the right.

Figure 33. Temperature

4.2.8 Flash Programming Main Menu

This menu allows you to select one of six choices. All choices except for items 4 and

9 require the Flash Write Enable jumpers TB5 1-2 and TB10 1-2 to be on the main

switch card, otherwise the Flash will NOT be reprogrammed. Selection 9 can reboot

the switch so that downloads of new fabric and/or port chip code can take effect.

Caution: Choice 3 will start storing the current configuration as soon as you select it,

it does NOT have a “Are you sure Y/N” dialog choice after you select choice 3!

  *** PORT STATISTICS ***

  *** Temperature Sensor Readings in degree C ***

Current Minimum Maximum

  Board Ambient : 31 31 32

  Fabric Chip :     45 45 46

  Portchip A : 57 57 58

  Portchip B : 42 42 43

Press 'q' to quit:

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
46
47
48
49
50
...
»

Содержание FibreMATRIX FC-76000 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для FibreMATRIX FC-76000 Series

Бренд: Eaton Страницы: 12

Бренд: Kramer Страницы: 61

Бренд: Aube Technologies Страницы: 118

Бренд: HMS Networks Страницы: 16

Бренд: Hall Technologies Страницы: 35

Бренд: Cudy Страницы: 2

Бренд: Waters Network Systems Страницы: 12

Бренд: Ableconn Страницы: 16

Бренд: Sarowin Страницы: 9

Cooper Power Systems LCR 6200 RFN

Бренд: Eaton Страницы: 8

Бренд: Free-Way Switch Страницы: 6

Бренд: Net Generation Страницы: 38

Liquipoint FTW33

Бренд: Endress+Hauser Страницы: 48

Бренд: Flamingo Страницы: 2

Ethernet Switch Boards

Бренд: Intel Страницы: 52

Бренд: Cable Electronics Страницы: 12

Signal Distribution Box SDB45

Бренд: Audiovox Страницы: 12

Бренд: Byte Delight Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды