DayStar DS-100c Скачать руководство пользователя страница 9

Страница: 9 / 53

DS-100C Operating Manual

IVPC Installation & Quick-Start

page 1

1.0 Installation & Taking IV Curves

Basic Description

The standard DS-100C Tracer has two user selectable current ranges (10 and

100 Amperes), three automatically selected voltage ranges (600, V, 60 V, and 6

Volts), two irradiance and two temperature measurement inputs. Unless

otherwise noted, this manual refers to standard DS-100C models.

Note: The three measurement voltage ranges listed here should not be confused

with the load ranges (V

HIGH

and V

LOW

) selected with the range switch.

A computer running the IVPC for Windows program controls the DS-Tracer.

(See the IVPC Reference Manual). The computer running the IVPC application

may be connected to the DS-Tracer by RS-232 serial or USB.

Most DS-Tracer operations are performed with the IVPC program. Refer to the

IVPC manual for details on operating the DS100C IV Tracer. However, the basic

steps for using the DS-Tracer are:

•

Connect the DS-Tracer to the computer (either RS-232 or USB).

•

Turn on the tracer power and connect DS-Tracer test leads to PV array.

•

Connect pyranometers and thermocouples to DS-Tracer.

•

Install and run IVPC for Windows (see the IVPC manual for details).

•

From File menu select New I-V Curve.

•

Enter curve information and take curve.

•

Save curve data.

To proceed with the Installation & Quick-Start, you will need the following:

•

DS-Tracer I-V curve tracer and test leads.

•

IVPC CD-ROM.

•

PC computer running the Microsoft Windows® operating system.

Содержание DS-100c






















































Результаты поиска

Содержание DS-100c

Отзывы:

Похожие инструкции для DS-100c

Бренды по названию

Популярные бренды

DayStar DS-100c, Руководство пользователя

Результаты поиска

Содержание DS-100c

Отзывы:

Похожие инструкции для DS-100c

Бренды по названию

Популярные бренды