DayStar DS-100c Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 53

background image

page C16

DS-100C Operating Manual

unplugged before the battery is fully charged. This occurrence does not indicate

a fully charged battery.

Aux Charge Power & Fuse

The Aux Charge connector is a standard banana jack connector used to

recharge the battery from a DC power source such as a PV module. Do not

exceed the input voltage. A fuse protects the tracer from excess current.

RS-232 Serial Port

All DS-Tracer operations are controlled with commands sent to the DS-Tracer

through this serial port or the USB port. This port is a standard 9 pin RS-232

port. This port is configured as a DCE device. Normally the DS-Tracer functions

are controlled with the IVPC software, but you can create your own software

using the DS-Tracer command codes described in section 6.0 DS-100C

Additional Capabilities.

The DS-Tracer uses the following RS-232 format:

9600 Baud
No parity
8 data bits
1 stop bit

Main USB Port

All DS-Tracer operations are controlled with commands sent to the DS-Tracer

through this USB port or the RS-232 port. This port is a standard USB Type-B

port. Normally the DS-Tracer functions are controlled with the IVPC software, but

you can create your own software using the DS-Tracer command codes

described in section 6.0 DS-100C Additional Capabilities.

Aux USB Port

This port supports auxiliary DS-100C operations This port is a standard USB

Type-A port. This port is NOT used to control the DS-100C IV tracer. It is meant

«
...
22
23
24
25
26
...
»

Содержание DS-100c






















































Отзывы:

Нет отзывов

Похожие инструкции для DS-100c

Бренд: Magellan Страницы: 119

RoadMate 1200 - Automotive GPS Receiver

Бренд: Magellan Страницы: 33

Бренд: Holux Страницы: 14

GPS Navigator GP-500 MARK-2

Бренд: Furuno Страницы: 160

Бренд: Hardi Страницы: 30

Бренд: Pentagram Страницы: 22

Бренд: MEGASTEK Страницы: 16

Бренд: Microsport Страницы: 27

Бренд: Sanav Страницы: 26

Бренд: Sanav Страницы: 43

Бренд: Sanav Страницы: 45

Бренд: Sanav Страницы: 79

Бренд: Lowrance Страницы: 30

Бренд: Loc8r Страницы: 6

Бренд: Dual Страницы: 13

Бренд: PORTMAN Страницы: 34

Бренд: Laminar Research Страницы: 29

Solar Bluetooth GPS Receiver

Бренд: Keomo Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды