DayStar DS-100c Скачать руководство пользователя страница 50

Страница: 50 / 53

page C42

DS-100C Operating Manual

Appendix C DS-100 USB Drivers

In order to use the DS-100C USB port for tracer control, the DS-100 USB drivers

must be installed on the computer running IVPC. Two drivers will be installed.

The primary driver will be a USB device driver labeled “DS-100 IV Tracer”. The

second driver will be a virtual COM port also labeled “DS-100 Tracer”. This

virtual COM port will function as a conventional COM port.

IVPC version 2.X and lower only work with COM ports and therefore require the

virtual COM port. New versions of IVPC will not need this virtual COM port, but

still require the USB driver installation.

IVPC 2.X and lower only support COM ports 1 through 4. Therefore after being

created, the virtual COM port must be assigned a COM port number in this

range. It is common for the operating system to assign a COM port number

outside this range, even if a COM port number from 1 to 4 is not in use.

Use the Windows OS device manager to change the COM port number assigned

to this virtual COM port. Often Windows will warn that this COM port is in use.

But if you know that it is not in use, you can reassign it to the necessary value

from 1 to 4. After changing the COM port assignment, it is best to restart the

computer to ensure proper operation.

Consult the Microsoft documentation and help system for details on using the

device manager.

Note: If you have a conventional RS-232 COM port available, there is no

advantage to using the DS-100C USB port and it is not necessary to install these

USB drivers. However, many modern notebook computers do not have COM

ports, and therefore it is necessary to install these DS-100 USB drivers.

The DS-100 USB drivers are located on the IVPC CD-ROM supplied with the

tracer in the DS-100 USB Drivers folder. This folder contains detailed instructions

on how to install the drivers for your version of the operating system.

Содержание DS-100c






















































Результаты поиска

Содержание DS-100c

Отзывы:

Похожие инструкции для DS-100c

Бренды по названию

Популярные бренды

DayStar DS-100c, Руководство пользователя

Результаты поиска

Содержание DS-100c

Отзывы:

Похожие инструкции для DS-100c

Бренды по названию

Популярные бренды