manualshive.com logo in svg

Datum Systems M7 Series, Инструкция по установке и эксплуатации

MACAP M7 Series представляет собой высококачественную кофемолку, обладающую мощным мотором и мельницей из нержавеющей стали. Для более подробных инструкций по эксплуатации продукта, вы можете скачать бесплатное руководство по эксплуатации с manualshive.com. Это необходимое руководство для успешного использования кофемолки.

Поделиться
Скачать
background image

M7/M7L/M7LT Modular Satellite Modem 

 

Maintenance 

M7/M7L/M7LT - Rev. 0.05 

 

3-109 

3.11.  Special Control Mechanisms 

The modem includes several special controls that were built in for specific customer systems, but are 
available in the standard modem.  These are not considered normal operation so care must be taken 
if they are used.  

 

Power-Up Behavior  

 

Analog Monitor Output  

 

RTS Monitor 

3.11.1.  Power-Up Behavior 

The modem can be set to always revert to the transmit carrier disabled on power-up. This might be 
useful for example in mobile environments where the antenna may not be deployed or aligned on 
each power-up cycle. Setting this option in the 

<Mod: IF - Mute>

 parameter 

to “Manual & Power 

Loss

“ allows such operation. 

In other cases the user may require that the modem always revert to a specific configuration on 
power-up. The normal behavior is for the modem to power-up with the last settings still in effect. One 
of the options in the Unit Configuration column is 

<Unit: Config 

– Power-Up>

. The default setting is 

“Last” which performs as the normal described above. A user can select any of the stored 
configurations to be recalled on each power-up cycle. This could be useful in a mobile environment or 
a DAMA system where a control channel is desired on each power-up. In a large system, units can 
be pre-set to a specific configuration during initial commissioning, but then easily changed to another 
configuration for normal operation.  

3.11.2.  Analog Monitor Output Operation 

The modem has a built-in function to output an analog voltage representing the current value of one 
of three internal parameters by setting the 

<Unit: Monitor - Mode> 

parameter. The available 

parameters that can be selected for this output are:  

 

Receive carrier level (Dmd CXR Level) 

 

Receive Eb/No (Dmd Eb/No) 

 

Transmit output power level (Mod CXR Level) 

The analog output can be tailored to the user requirements through any of the control interfaces. The 
output the processor allows control of the full scale voltage by setting the 

<Unit: Monitor 

– Full>

 

parameter to a range of +1.0 Volts to +10.0 Volts and the slope by setting the 

<Unit: Monitor 

– 

Output Slope>

 parameter to positive or negative. These two settings control the output slope (gain 

and direction) of this analog output voltage.   

To illustrate consider the example of using the Receive carrier level for the monitor output to 
automatic antenna positioning equipment.  For this example, the modem has a carrier input range of 
–20 to –60 dBm.  

If the antenna auto-track controller requires a positive slope between 0 and +10 Volts, where +10 
Volts represents the maximum received signal level, set the 

<Unit: Monitor 

– Full>

 parameter to 

“+10.0” and the 

<Unit: Monitor 

– Output Slope> 

parameter to “Negative”. These settings have the 

effect of inverting the slope of the AGC signal and setting the gain of the voltage to match the input to 
the antenna controller. 

NOTE:  The output voltage is always a positive voltage. 

The analog output presented at pints 5 (+voltage) and 6 (gnd) on the rear panel Alarms connector 
(J6).  The voltage pin has a1k

Ω output impedance, protecting the driver circuitry from shorts. 

Содержание M7 Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M7 Series

MailASail Red Box Quick Start Manual preview
Red Box
Бренд: MailASail Страницы: 2
NAL RESEARCH CORPORATION A3LA-RG Quick Start Manual preview
A3LA-RG
Бренд: NAL RESEARCH CORPORATION Страницы: 3
Optelecom 9525AY Installation And Operation Manual preview
9525AY
Бренд: Optelecom Страницы: 26
SAGEMCOM Sunrise Internet Box User Manual preview
Sunrise Internet Box
Бренд: SAGEMCOM Страницы: 2
Airlink101 AirLink Raven X for Bell User Manual preview
AirLink Raven X for Bell
Бренд: Airlink101 Страницы: 37
Zte 403ZT Quick Start Manual preview
403ZT
Бренд: Zte Страницы: 7
Fujitsu DSL Modem Installation Manual preview
DSL Modem
Бренд: Fujitsu Страницы: 24
Fujitsu 3G Mini-Card ModemGobi 3000 Regulatory And Safety Information Manual preview
3G Mini-Card ModemGobi 3000
Бренд: Fujitsu Страницы: 12
Fujitsu FC9660RA12 Installation Manual preview
FC9660RA12
Бренд: Fujitsu Страницы: 25
Fujitsu FMWT-401 Getting Started Manual preview
FMWT-401
Бренд: Fujitsu Страницы: 44
Fujitsu ADSL USB Modem User Manual preview
ADSL USB Modem
Бренд: Fujitsu Страницы: 100
Toro TouchNet 89-9150 Installation Instructions preview
TouchNet 89-9150
Бренд: Toro Страницы: 2
Zoom 3025 Specification preview
3025
Бренд: Zoom Страницы: 2
Zoom 1099 Series User Manual preview
1099 Series
Бренд: Zoom Страницы: 32
Zoom 1070 Series User Manual preview
1070 Series
Бренд: Zoom Страницы: 33
Vega NB-15 User Manual preview
NB-15
Бренд: Vega Страницы: 25
Vega SH-2 User Manual preview
SH-2
Бренд: Vega Страницы: 34
Javad HPT104BT Series Operator'S Manual preview
HPT104BT Series
Бренд: Javad Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды