Datamax PrintPAD 1700 Скачать руководство пользователя страница 89

Страница: 89 / 145

PrintPAD CN70/70e USER'S GUIDE

Printing a Self-Test

1. Open the printer's cover.
2. Press and hold the red self-test button for 4-5 seconds, until the printer starts to print (Figure 13).

3. After printing starts, release the red self-test button.

Configuring the Printer

The printer has many configurable settings. To configure or upgrade firmware, download the Windows

configuration program

Using the Printer Data Cables

1. Select the appropriate cable for use with the host and/or device you are using.
2. Insert the plug into the printer’s data port (Figure 14).

Note: Do not close the lid or damage will occur to the cable. The data cable is intended only for reflashing the

printer.

Figure 13

Figure 14

Содержание PrintPAD 1700


















































































































































Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды

Datamax PrintPAD 1700, Руководство пользователя

Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды