Datamax PrintPAD 1700 Скачать руководство пользователя страница 42

Страница: 42 / 145

PrintPAD CN3/4 & PrintPAD CN3e/4e USER'S GUIDE

Compatible Handheld Computers

Installing the Battery Spacers

1. Verify the battery type being used in the Intermec® CN3 or CN4 Handheld unit.



Standard Battery (Model AB8)



Extended Battery (Model AB9)

If using the Standard Battery, install the Battery Spacers using a screwdriver.

Note: The PrintPAD CN3/4 & PrintPAD CN3e/4e are intended for use with UL Listed Accessory Handheld Computer

Intermec CN3, CN3e, CN4, and CN4e.

Note: If the extended battery is not being used, the battery spacers must be installed. The battery spacers do not

come installed.

Caution: Over-torquing the screws will strip the screw holes. It is recommended that the screws be tightened by

hand.

Note: The Intermec CN3e handheld unit does not require battery spacers.

Figure 6

Figure 7

Содержание PrintPAD 1700


















































































































































Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Datamax PrintPAD 1700, Руководство пользователя, Страница: 42 / 145

Результаты поиска

Содержание PrintPAD 1700

Отзывы: