Datamax PrintPAD 1700 Скачать руководство пользователя страница 119

Страница: 119 / 145

Chapter 3 — Printer Configuration

PrintPAD Series CN70/70e & CN51 User Guide

Setup Bluetooth Parameters

Radio printers are configured with the default factory settings. To determine
your printer’s radio configuration, print a self

test. See “Printing a Self

Test” on

page 11. If you have multiple printers, configure them specifically for use in your
environment.

For proper system operation, set the following parameters on your printer and
host computer.

Bluetooth Parameters

•

Device Name

•

Authentication (This must be set to “Yes” for Android devices, and Windows
7 and above host PCs)

•

Bondable

•

Discoverable

•

Connectable

•

Encryption

Contact your network administrator to verify the proper radio settings for your
environment.

Note: The following information applies to printers with Bluetooth capabilities.

Содержание PrintPAD 1700


















































































































































Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды

Datamax PrintPAD 1700, Руководство пользователя

Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды