Datamax PrintPAD 1700 Скачать руководство пользователя страница 123

Страница: 123 / 145

Chapter 4 — Printer Options

PrintPAD Series CN70/70e & CN51 User Guide

External Charge Contacts

External Charging: External charge-capable printers have two charging contact points
located on the back of the printer’s case.

External charge

capable printers can be used with various Datamax

O’Neil by

Honeywell accessories, such as the truck mount bracket. When an external
charge

capable printer is mounted to one of these accessories, the printer’s

batteries are automatically charged.

When using with an accessory, verify proper position of printer on external
charge contacts. Refer to the status LEDs for proper charging.

For more information, see the instruction sheets included with the accessories.

Note: The following information applies to printers installed with the external
charge capabilities.

Use of any product not approved by Honeywell for use with their printers
could cause damage to the batteries or printer and will void the warranty.

Do NOT plug the DC jack power supply into the printer if the printer is
being used with an external charging bracket, mount or stand.

Failure to observe these instructions or warnings specified in the
documentation may result in damage to your printer. Honeywell does not
accept liability for resulting damage or injuries.

Содержание PrintPAD 1700


















































































































































Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды

Datamax PrintPAD 1700, Руководство пользователя

Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды