Datamax PrintPAD 1700 Скачать руководство пользователя страница 60

Страница: 60 / 145

PRINTPAD 7900 USER'S GUIDE

Using PrintPAD LEDs, Buttons, and Audio

Indicators

Charge LED Indicators

LED Indicators

Blue RF Power LED Indicators

LED

State of Charge

Action

Solid red

Charge in progress.

Wait for green LED.

Green

Charge completed.

None.

Red flash-slow Battery is too cold.

Battery is disconnected.

Change environment.
Connect battery.

Red flash-fast High temperature.

Change environment.

Red/orange
flash-slow

Battery voltage is very
low.

Wait for solid red.
Restart charge.

Red/orange
flash-fast

Battery is disconnected. Connect battery.

Orange flash-
slow

Charge timeout.

Restart charge.

LED

Description

Blue flash - fast

RF power is on and printer is awake.

Blue flash - slow RF power is on and printer is asleep.
Off

RF power is off.

Содержание PrintPAD 1700


















































































































































Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Бренды по названию

Популярные бренды

Datamax PrintPAD 1700, Руководство пользователя

Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Бренды по названию

Популярные бренды