Datamax PrintPAD 1700 Скачать руководство пользователя страница 5

Страница: 5 / 145

PrintPAD MC65 USER'S GUIDE

The Charge LED flashes red when charging and flashes green when fully charged. The Charge LED is visible when the

printer's lid is open or closed. A complete charge takes approximately 7-9 hours. For more information on the Charge

LEDs, see

PrintPAD MC65 LEDs and Indicators on page 6

Determining Battery Condition

You can determine the relative battery condition by printing a self-test. For more information, see

Printing a Self-Test

on page 5

. On the printout, “Battery Volt” varies between 6.8 and 8.4 volts.

Installing the Driver

1. Go to datamax-oneil and click

Support

to obtain the appropriate driver for the PrintPAD MC65.

2. Install the driver onto the handheld computer.

Using a Handheld Computer (HHC)

1. Insert the handheld into the cavity by sliding it in from the top.
2. Press down until the handheld is fully latched and seated (Figure 5).

Compatible Handheld Computers

Note: To obtain full battery capacity, a new battery must cycle through two to three charges. To restart a charge,

unplug the power cord. Wait 30 seconds, then replug the power cord.

The MC65 Handheld Computer will charge while power is plugged into the DC power port.

Caution: Do not plug DC power into the internal and external power ports at the same time.

Do not plug the DC power supply into the printer if the printer is being charged by means of external charge

contacts.

Caution: There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries

according to the instructions.

The operating temperature of this portable printer is 50°

C. However, the operating temperature when used with

Datamax-O’Neil power supply for charging the portable printer is limited to 40° C. Charge the printer in a suitable

location that meets this temperature requirement.

(For US/Canada) Use only the Datamax-O’Neil part number 220240-100 power supply with this product.

Note: Before using a MC65 and the printer, it is necessary that the appropriate USB driver is installed. Refer to the

USB Installation Guide for more information.

Note: The PrintPad MC65/67 series is intended for use with the UL Listed Accessory Handheld Computer Askey

Computer Corp MC65 series or the UL Listed Accessory Handheld Computer Askey Computer Corp MC67 series.

Содержание PrintPAD 1700


















































































































































Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды

Datamax PrintPAD 1700, Руководство пользователя

Результаты поиска

Содержание PrintPAD 1700

Отзывы:

Похожие инструкции для PrintPAD 1700

Бренды по названию

Популярные бренды