Data Aire dap4 touch Скачать руководство пользователя страница 64

Страница: 64 / 112

64 • dap4 User Manual

The following will be displayed (values are for reference only):

Move the cursor by pressing the ENTER key. Move the cursor to change the setting.

The following can be changed by pressing the DOWN key:

Channel – there are six (6) selections (Y1, Y2, Y3, Y4, Y5 and Y6). There are five Analog

outputs available. DO NOT ASSIGN THE SAME CHANNEL ON MORE THAN ONE ANA-

LOG OUTPUT.

Action: there are two choices; DIRECT AND REVERSE

Minimum: the range is from 0.0vdc to 10.0vdc

Maximum: the range is from 0.0vdc to 10.0vdc

To return to another Input or Output screen, with the cursor in the title block, press the UP or

DOWN key to scroll through the selections

To exit Menu L – Configure I/O, with the cursor in the title block, press the Menu key. The screen

will display the Menus.

▼ Press the Esc key to return to the normal operating mode.

Analog Output Config

Channel: Y3

Action: DIRECT

Minimum 0.0vdc

Maximum: 0.0vdc

Содержание dap4 touch

















































































































Результаты поиска

Содержание dap4 touch

Отзывы:

Похожие инструкции для dap4 touch

Бренды по названию

Популярные бренды

Data Aire dap4 touch, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание dap4 touch

Отзывы:

Похожие инструкции для dap4 touch

Бренды по названию

Популярные бренды