Data Aire dap4 touch Скачать руководство пользователя страница 26

Страница: 26 / 112

26 • dap4 User Manual

MENU G – NETWORK CONFIG

MENU G allows selection of BMS protocol. (Service Level password is required for entry)

Once password has been entered, press the UP or DOWN key until “G. Network Config” appears

and is highlighted. Press the ENTER key.

The following will be displayed (values are for reference only):

Only the protocol can be changed. The selections are as follows:

LON, BACNET, PCOLOAD, MODBUS, MODEM, CAREL, N/A

Once the selection has been made, press the ENTER key and the cursor will move to the title

block.

To move to the next screen, press the DOWN key.

The following will be displayed (values are for reference only):

The address can be a value from 0 to 999

The available baud rates are: 1200, 2400, 4800, 9600, 19200

Once the selection has been made, press the ENTER key to move the cursor to the title block.

▼ Press the Esc key to return to the Main Menu. Scroll to the next menu to be viewed is high-

lighted or press the Esc again to return to the normal operating mode.

Bms Configuration

BMS Port 1
Protocol: MODBUS

Bms Configuration

BMS Port 1
Address 1
Baud Rate

19200

Содержание dap4 touch

















































































































Результаты поиска

Содержание dap4 touch

Отзывы:

Похожие инструкции для dap4 touch

Бренды по названию

Популярные бренды

Data Aire dap4 touch, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание dap4 touch

Отзывы:

Похожие инструкции для dap4 touch

Бренды по названию

Популярные бренды