Dannmar DLR-6 Скачать руководство пользователя

Страница: 7 / 40

DLR-6/6P Low-Rise Scissor Lifts

P/N 5900254 — Rev. A — September 2020

Installation Checklist

Following are the steps needed to install your Lift. Perform them in the order shown.

☐

1. Review the installation Safety Rules.

☐

2. Make sure you have the necessary Tools.

☐

3. Select the Installation Site.

☐

4. Understand Longitudinal Shift.

☐

5. Check clearances.

☐

6. Unpack and locate the Lift.

☐

7. Assemble the Portable Stand (DLR-6

only).

☐

8. Attach the Power Unit to the Portable Stand (DLR-6

only).

☐

9. Assemble the Tow Cart (DLR-6

only).

☐

10. Raise the Platforms Off the Base (DLR-6 only).

☐

11. About Embedment (DLR-6 only).

☐

12. Anchor the Bases (DLR-6 only).

☐

13. Anchor the Power Unit Stand (DLR-6 only).

☐

14. Install the Wheels (DLR-6

only).

☐

15. Understand Hydraulic Fluid Contamination.

☐

16. Connect the Hydraulic Hose.

☐

17. Add Hydraulic Fluid.

☐

18. Reconfigure the Power Unit to 230 VAC Power (optional).

☐

19. Connect to Power.

☐

20. Test the Lift.

☐

21. Review the Final Checklist.

Содержание DLR-6








































Результаты поиска

Содержание DLR-6

Отзывы:

Похожие инструкции для DLR-6

Бренды по названию

Популярные бренды

Dannmar DLR-6, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DLR-6

Отзывы:

Похожие инструкции для DLR-6

Бренды по названию

Популярные бренды