Dannmar DLR-6 Скачать руководство пользователя | Manualshive

Страница: 2 / 40

background image

Manual.

DLR-6/6P Low-Rise Scissor Lift,

Installation and Operation Manual

, Manual Part Number 5900254,

Manual Revision A, released September 2020.

Copyright.

Copyright © 2020 by BendPak Inc. All rights reserved. You may make copies of this document if you

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain

any rights to this content, and you will not use the copies for commercial purposes.

Trademarks.

Dannmar and the Dannmar logo are registered trademarks of BendPak Inc. All other company,

product, and service names are used for identification only. All trademarks and registered trademarks mentioned
in this manual are the property of their respective owners.

Limitations.

Every effort has been made to ensure complete and accurate instructions are included in this

manual. However, product updates, revisions, and/or changes may have occurred since this manual was

published. BendPak reserves the right to change any information in this manual without incurring any obligation for

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual.

Warranty.

The Dannmar warranty is more than a commitment to you: it is also a commitment to the value of

your new product. Contact your nearest Dannmar dealer or visit the Dannmar website.

Safety.

Your product was designed and manufactured with safety in mind. However, your safety also depends

on proper training and thoughtful operation. Do not install, operate, maintain, or repair the unit without reading and

understanding this manual and the labels on the unit;

do not use your Lift unless you can do so safely!

Owner Responsibility.

In order to ensure operator safety and maintain your product properly, it is the

responsibility of the product owner to read and follow these instructions:

• Follow all setup, operation, and maintenance instructions.

• Make sure product setup and use conforms to all applicable local, state, and federal codes, rules, and

regulations, such as state and federal OSHA regulations and electrical codes.

• Read and follow all safety instructions. Keep them readily available for operators.

• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.

• Do not operate the product until you are certain all parts are in place and operating correctly.

• Carefully inspect the product on a regular basis and perform all maintenance as specified.
• Service and maintain the unit only with approved replacement parts.

• Keep all instructions permanently with the product and make sure all labels are clean and visible.

•

Only use the Lift if it can be used safely!

Unit Information.

Enter the Model Number, Serial

Number, and the Date of Manufacture from the label on

your unit. This information is required for part or

warranty issues.

Model:

Serial:

Date of Manufacture:

«
1
2
3
4
...
»

Содержание DLR-6









































Отзывы:

Нет отзывов

Похожие инструкции для DLR-6

Бренд: Genie Страницы: 37

Бренд: Genie Страницы: 33

Бренд: Terex Страницы: 155

Бренд: Oshkosh Corporation Страницы: 110

Бренд: jcb Страницы: 24

Genie Z-45/25J Bi-Energy

Бренд: Terex Страницы: 69

Бренд: Terex Страницы: 73

miniLIFT CLASSIC

Бренд: Astra Страницы: 28

Бренд: Genie Страницы: 183

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды