Dannmar DLR-6 Скачать руководство пользователя | Manualshive

Страница: 23 / 40

background image

DLR-6/6P Low-Rise Scissor Lifts

23

P/N 5900254 — Rev. A — September 2020

Connect to Power

The Power Unit comes fully assembled from the factory, configured for 115 VAC operation. An
Electrician is

not

required to connect to a 115 VAC power source.

The Power Unit can also be reconfigured for 230 VAC. Refer to

Reconfigure the Power Unit to

230 VAC (optional)

for details.

⚠

DANGER

Reconfiguring the Power Unit to use 230 VAC power

requires

a licensed, certified

Electrician. Attempting to reconfigure your Power Unit without using an Electrician

voids your warranty and puts everyone who uses the Lift in danger.

The Power Unit for the Lift is 115 VAC

or

230 VAC, 50/60 Hz, 1 phase. The circuit must be grounded

and protected with a time-delay fuse or circuit breaker. For a 115 VAC, 1 phase circuit, use a 20 amp

or greater breaker. For a 230 VAC, 1 phase circuit, use a 25 amp or greater breaker.

Important

: The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make

sure to implement them once the unit is connected to a power source.

⚠

CAUTION

The Power Unit’s motor is

not

thermally protected.

To connect to 115 VAC power

:

1.

Find the Power Cord on the Power Unit.

2.

Verify that the Power Cord has a 115 VAC plug on the end and that it has

not

been reconfigured

to operate at 230 VAC.

3.

Plug the 115 VAC plug into a

grounded

115 VAC outlet.

To connect to 230 VAC power

:

1.

Verify that the supplied Power Unit has been reconfigured for 230 VAC operation; the Power Unit

comes from the factory configured for 115 VAC.
The process for reconfiguring the Power Unit to 230 VAC operation is described in

Reconfigure

the Power Unit to 230 VAC (optional)

2.

When you have confirmed that the Power Unit has been reconfigured to 230 VAC operation, find
the 230 VAC plug on the end of the Power Cord.
If the Power Cord still has a 115 VAC plug, then the supplied Power Unit was

not

successfully

converted to 230 VAC operation. Contact the Electrician or your Supervisor

before

proceeding.

3.

Plug the 230 VAC plug into a

grounded

230 VAC outlet.

«
...
21
22
23
24
25
...
»

Содержание DLR-6









































Отзывы:

Нет отзывов

Похожие инструкции для DLR-6

Бренд: Torin Страницы: 31

Sinoboom GTJZ1412

Бренд: Elevated Access Страницы: 49

Бренд: EAE Страницы: 40

Бренд: IDECH Страницы: 13

Бренд: ATH-Heinl Страницы: 450

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды