Dannmar DLR-6 Скачать руководство пользователя

Страница: 5 / 40

DLR-6/6P Low-Rise Scissor Lifts

P/N 5900254 — Rev. A — September 2020

Components

Lift components include:
•

Power Unit

. Provides Hydraulic Fluid to the Hydraulic Cylinders, which raises the Platforms.

•

Platforms

. Flat steel plates that raise and lower. The Lift Pads, which sit on the Platforms, make

contact with the underside of the Vehicle.

•

Power Unit Stand

. DLR-6 only. Holds the Power Unit. Bolts to the ground.

•

Portable Stand

. DLR-6P only. Holds the Power Unit. Freestanding, moveable.

•

Tow Cart

. DLR-6P only. Used to move the Lift to a different location.

•

Fixed Ramps

. Allows Vehicles to drive on to and off of the Platforms.

•

Hinged Ramps

. Allows Vehicles to drive on to and off of the Platforms.

•

Base

. The bottom of the Lift. Has the holes for the Anchor Bolts for the DLR-6.

•

Hydraulic Cylinder

. Pushes the Platforms up to raise a Vehicle, down to lower a Vehicle.

•

Hydraulic Hose

. Moves the Hydraulic Fluid from the Power Unit to the Hydraulic Cylinder.

•

Safety Locks

. Hold the Platforms up, once

engaged

. Always leave the Lift either engaged on a

Safety Lock or lowered to the ground.

•

Lift Pads

. Rubber blocks that make contact with the manufacturer-recommended Lifting Points.

•

Wheel Assemblies

. DLR-6P only. Raises the Hinged Ramp end of the Lift off the ground,

allowing the Lift to move to a different location.

Not shown

Содержание DLR-6








































Результаты поиска

Содержание DLR-6

Отзывы:

Похожие инструкции для DLR-6

Бренды по названию

Популярные бренды

Dannmar DLR-6, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DLR-6

Отзывы:

Похожие инструкции для DLR-6

Бренды по названию

Популярные бренды