DLR-6/6P Low-Rise Scissor Lifts
24
P/N 5900254 — Rev. A — September 2020
Test the Lift
Before putting your Lift into normal operation, we recommend raising and lowering it a few times with a
typical Vehicle on it.
Tip
Residual air in the Hydraulic System can cause the Lift to shake, move erratically, or
squeak; this is normal when you first start using the Lift. It will soon stop doing this,
as the Hydraulic System is self-bleeding.
To test your Lift
:
1.
Check the items listed in
2.
Make sure both Platforms are fully lowered, then drive the Vehicle over the Platforms and situate it
correctly.
⚠
CAUTION
Make sure to situate the Vehicle so that neither the front nor the rear wheels are
over the Platforms. If you raise the Platforms with the wheels over the Platforms,
you could damage the wheels.
3.
Put the Vehicle in park, put on the parking brake, and turn off the Vehicle.
If the Vehicle is a manual transmission, put it into first gear before turning it off.
4.
Walk around the Vehicle and make sure there are no obstructions or any other issues that will
interfere with the raising of the Platforms.
5.
Locate the manufacturer’s recommended Lifting Points for the Vehicle you are raising.
If you are unsure where the Lifting Points are, consult
Vehicle Lifting Points for Frame Engaging
Lifts
, available on the ALI store (
) or the manufacturer of the Vehicle.
⚠
WARNING
Do not ‘eyeball’ the best location for the Lift Pads.
The Lift Pads must hit the
manufacturer’s recommended Lifting Points
. If you do not, the Vehicle
could become unstable and fall, which could damage the Vehicle, damage the Lift,
or injure or even kill anyone under the Vehicle.
6.
Put the Lift Pads under the Vehicle so that they are
directly under
the Lifting Points.
7.
On the Power Unit, press and hold the
Raise
button to raise the Lift until
just before
the Lift
Pads make contact with the Lifting Points on the underside of the Vehicle.
8.
Make sure the Lift Pads will make solid contact with the Lifting Points when raised further.
9.
Raise the Lift until the Lift Pads contact the underside of the Vehicle and raise the tires of the
Vehicle a few inches off the ground.
10.
Visually check to make sure the Lift Pads are making solid contact with the Lifting Points.
If any of the Lift Pads are
not
making solid contact with the Lifting Points, lower the Lift and adjust
the Lift Pads so that they make better contact.
11.
Rock the Vehicle to make sure the Vehicle is stable and balanced.
If the Vehicle is
not
stable and balanced, lower the Lift back to the ground and start over.
If the Vehicle
is
stable and balanced, it is safe to raise further.
Содержание DLR-6
