background image

Application Guidelines

18

AB141686422149en-US0401

Sound and vibration management

Running sound level

Stopping sound level

Sound generation in a  
refrigeration system and air  
conditioning system

Compressor sound radiation

During start-up transients, it is natural for the 
compressor sound level to be slightly higher 
than during normal running. Danfoss scroll 

compressors exhibit very little increased start-up 
transient sound.

VRJ scroll compressors are designed with 
optimised discharge ports and wrap geometry 

to reduce the sound level when a compressor is 
running.

VRJ scroll compressors have very low shutdown 
sound due to minimal volume of discharge 
volume to push scrolls in reverse at shutdown. 

Due to this small re-expansion, there is no 
internal break mechanism required to prevent 
reverse spin of the scroll set.

Typical sound and vibration in refrigeration and 
air conditioning systems encountered by design 
and service engineers may be broken down into 
the following three source categories.

Sound radiation:

 This generally takes an 

airborne path.

Mechanical vibrations:

 These generally extend 

along the parts of the unit and structure.

Gas pulsation: 

This tends to travel through the 

cooling medium, i.e. the refrigerant.
The following sections will focus on the causes 
and methods of mitigation for each of the above 
sources.

For sound radiating from the compressor, the 
emission path is airborne and the sound waves 
are travelling directly from the machine in all 
directions.

The VRJ scroll compressor is designed to be quiet 
and the frequency of the sound generated is 
pushed into the higher ranges, which not only 
are easier to reduce but also do not generate the 
penetrating power of lower-frequency sound.

Use of sound-insulation materials on the inside of 
unit panels is an effective means of substantially 

reducing the sound being transmitted to the 
outside. Ensure that no components capable 
of transmitting sound/vibration within the unit 
come into direct contact with any non-insulated 
parts on the walls of the unit.

Because of the Danfoss unique design of a full-
suction gas & oil cooled motor, compressor body 
insulation across its entire operating range is 
possible.

Starting sound level

Sound level vs Speed 

56

58

60

62

64

66

68

70

72

74

76

78

45/130

4200

45/130

3600

45/100

3600

45/100

2400

45/100

1800

45/100

900

Condition (Tsat(suction) / Tsat (discharge) and speed (RPM)

S

o

u

n

d

 p

o

we

le

ve

(d

B

A

)

    

Содержание VRJ

























Отзывы: