Danfoss VLT HVAC Drive FC 102 Скачать руководство пользователя

Страница: 49 / 82

3 = Third drive module from left (in 4-module
module systems).

4 = Fourth drive module from left (in 4-module
module systems).

ALARM 247, Power card temperature

This alarm is only for multi-drive systems. It is equivalent to

alarm 69, Power card temperature

. The report value in the

alarm log indicates which drive module generated the
alarm:

1 = Left drive module.

2 = Second drive module from left.

3 = Third drive module from left (in 4-module
module systems).

4 = Fourth drive module from left (in 4-module
module systems).

ALARM 248, Illegal power section configuration

This alarm is only for multi-drive systems. It is equivalent to

alarm 79, Illegal power section configuration

. The report

value in the alarm log indicates which drive module
generated the alarm:

1 = Left drive module.

2 = Second drive module from left.

3 = Third drive module from left (in 4-module
module systems).

4 = Fourth drive module from left (in 4-module
module systems).

Troubleshooting

Check the following:

•

The current scaling cards on the MDCIC.

WARNING 250, New spare part

A component in the drive system has been replaced.

Troubleshooting

•

Reset the drive system to restore normal
operation.

WARNING 251, New typecode

The power card or other components are replaced, and the
type code has changed.

Maintenance, Diagnostics, a...

User Guide

MG37L202

Содержание VLT HVAC Drive FC 102



















































































Результаты поиска

Содержание VLT HVAC Drive FC 102

Отзывы:

Похожие инструкции для VLT HVAC Drive FC 102

Бренды по названию

Популярные бренды

Danfoss VLT HVAC Drive FC 102, Руководство пользователя

Результаты поиска

Содержание VLT HVAC Drive FC 102

Отзывы:

Похожие инструкции для VLT HVAC Drive FC 102

Бренды по названию

Популярные бренды