Danfoss VLT HVAC Drive FC 100 Series, Руководство по программированию, Страница: 55 / 122

5-40 Function Relay
Array (Relay 1 [0], Relay 2 [1])
Select options to define the function of the relays.
The selection of each mechanical relay is realized in an array
parameter.
Option: Function:
[12] Out of current
range Motor current is outside range set in
4-50 Warning Current Low and
4-51 Warning Current High .
[13] Below current,
low Motor current is lower than set in
4-50 Warning Current Low .
[14] Above current,
high Motor current is higher than set in
4-51 Warning Current High .
[16] Below speed,
low
[17] Above speed,
high
[19] Below feedback,
low
[20] Above feedback,
high
[21] Thermal warning The thermal warning turns on when the
temperature exceeds the limit in motor,
adjustable frequency drive or thermistor.
[22] Ready, no
thermal warning The adjustable frequency drive is ready
for operation and no over-temperature
warning is present.
[23] Remote, ready,
no thermal
warning The adjustable frequency drive is ready
for operation in auto mode, and no
over-temperature warning is present.
[24] Ready, Voltage
OK The adjustable frequency drive is ready
for operation and AC line voltage is
within the specified voltage range.
[25] Reverse Motor runs/is ready to run clockwise
when logic = 0 and counter clockwise
when logic = 1. Output changes as soon
as reversing signal is applied.
[26] Bus OK Active communication (no timeout) via
serial communication port.
[35] External Interlock See digital input.
[36] Control word bit
11 Bit 11 in the control word controls the
relay.
[37] Control word bit
12 Bit 12 in control word controls relay.
[41] Below reference,
low
[42] Above ref, high
[45] Bus Control
5-40 Function Relay
Array (Relay 1 [0], Relay 2 [1])
Select options to define the function of the relays.
The selection of each mechanical relay is realized in an array
parameter.
Option: Function:
[60] Comparator 0 See parameter group 13-1*. If
Comparator 0 is evaluated as TRUE, the
output will go high. Otherwise, it will be
low.
[61] Comparator 1 See parameter group 13-1*. If
Comparator 2 is evaluated as TRUE, the
output will go high. Otherwise, it will be
low.
[62] Comparator 2 See parameter group 13-1*. If
Comparator 2 is evaluated as TRUE, the
output will go high. Otherwise, it will be
low.
[63] Comparator 3 See parameter group 13-1*. If
Comparator 3 is evaluated as TRUE, the
output will go high. Otherwise, it will be
low.
[64] Comparator 4 See parameter group 13-1*. If
Comparator 4 is evaluated as TRUE, the
output will go high. Otherwise, it will be
low.
[65] Comparator 5 See parameter group 13-1*. If
Comparator 5 is evaluated as TRUE, the
output will go high. Otherwise, it will be
low.
[70] Logic rule 0 See parameter group 13-4*. If Logic
Rule 0 is evaluated as TRUE, the output
will go high. Otherwise, it will be low.
[71] Logic rule 1 See parameter group 13-4*. If Logic
Rule 1 is evaluated as TRUE, the output
will go high. Otherwise, it will be low.
[72] Logic rule 2 See parameter group 13-4*. If Logic
Rule 2 is evaluated as TRUE, the output
will go high. Otherwise, it will be low.
[73] Logic rule 3 See parameter group 13-4*. If Logic
Rule 3 is evaluated as TRUE, the output
will go high. Otherwise, it will be low.
[74] Logic rule 4 See parameter group 13-4*. If Logic
Rule 4 is evaluated as TRUE, the output
will go high. Otherwise, it will be low.
[75] Logic rule 5 See parameter group 13-4*. If Logic
Rule 5 is evaluated as TRUE, the output
will go high. Otherwise, it will be low.
Parameters
VLT
®
HVAC Basic Drive Programming Guide
MG18B222 - VLT
®
is a registered Danfoss trademark 3-27
3 3