Danfoss VLT AutomationDrive Скачать руководство пользователя страница 34

Страница: 34 / 281

The following parameters are relevant for the Process Control

Parameter

Description of function

7-20 Process CL Feedback 1 Resource

Select from which Source (i.e. analog or pulse input) the Process PID should get its feedback

7-22 Process CL Feedback 2 Resource

Optional: Determine if (and from where) the Process PID should get an additional feedback signal. If

an additional feedback source is selected the two feedback signals will be added together before

being used in the Process PID Control.

7-30 Process PID Normal/ Inverse Control

Under [0] Normal operation the Process Control will respond with an increase of the motor speed if

the feedback is getting lower than the reference. In the same situation, but under [1] Inverse

operation, the Process Control will respond with a decreasing motor speed instead.

7-31 Process PID Anti Windup

The anti windup function ensures that when either a frequency limit or a torque limit is reached, the

integrator will be set to a gain that corresponds to the actual frequency. This avoids integrating on an

error that cannot in any case be compensated for by means of a speed change. This function can be

disabled by selecting [0] “Off”.

7-32 Process PID Start Speed

In some applications, reaching the required speed/set point can take a very long time. In such

applications it might be an advantage to set a fixed motor speed from the frequency converter before

the process control is activated. This is done by setting a Process PID Start Value (speed) in

7-32 Process PID Start Speed

7-33 Process PID Proportional Gain

The higher the value - the quicker the control. However, too large value may lead to oscillations.

7-34 Process PID Integral Time

Eliminates steady state speed error. Lower value means quick reaction. However, too small value may

lead to oscillations.

7-35 Process PID Differentiation Time

Provides a gain proportional to the rate of change of the feedback. A setting of zero disables the

differentiator.

7-36 Process PID Diff. Gain Limit

If there are quick changes in reference or feedback in a given application - which means that the error

changes swiftly - the differentiator may soon become too dominant. This is because it reacts to

changes in the error. The quicker the error changes, the stronger the differentiator gain is. The differ-

entiator gain can thus be limited to allow setting of the reasonable differentiation time for slow

changes.

7-38 Process PID Feed Forward Factor

In application where there is a good (and approximately linear) correlation between the process

reference and the motor speed necessary for obtaining that reference, the Feed Forward Factor can be

used to achieve better dynamic performance of the Process PID Control.

5-54 Pulse Filter Time Constant #29

(Pulse term. 29),

5-59 Pulse Filter Time Constant #33

(Pulse term. 33),

6-16 Terminal 53 Filter Time Constant

(Analog term

53),

6-26 Terminal 54 Filter Time Constant

(Analog

term. 54)

If there are oscillations of the current/voltage feedback signal, these can be dampened by means of a

low-pass filter. This time constant represents the speed limit of the ripples occurring on the feedback

signal.

Example: If the low-pass filter has been set to 0.1s, the limit speed will be 10 RAD/sec. (the reciprocal

of 0.1 s), corresponding to (10/(2 x π)) = 1.6 Hz. This means that all currents/voltages that vary by

more than 1.6 oscillations per second will be damped by the filter. The control will only be carried out

on a feedback signal that varies by a frequency (speed) of less than 1.6 Hz.

The low-pass filter improves steady state performance but selecting a too large filter time will

deteriorate the dynamic performance of the Process PID Control.

Introduction to FC 300

FC 300 Design Guide

MG.33.BD.02 - VLT

is a registered Danfoss trademark

Содержание VLT AutomationDrive


























































































































































































































































































Результаты поиска

Содержание VLT AutomationDrive

Отзывы:

Danfoss VLT AutomationDrive, Руководство по конструкции, Страница: 34 / 281

Результаты поиска

Содержание VLT AutomationDrive

Отзывы: