Danfoss VLT AutomationDrive FC 300, Руководство по программированию

Страница: 127 / 219

13-01 Start Event
Option: Function:
[6] Current limit Current limit [6] The motor current limit,
set in 4-18 Current Limit , has been
exceeded.
[7] Out of current
range Out of current range [7] The motor current
is outside the range set in 4-18 Current
Limit .
[8] Below I low Below I low [8] The motor current is lower
than set in 4-50 Warning Current Low .
[9] Above I high Above I high [9] The motor current is
higher than set in 4-51 Warning Current
High .
[10] Out of speed
range
Out of speed range [10] The speed is
outside the range set in 4-52 Warning
Speed Low and 4-53 Warning Speed High .
[11] Below speed low Below speed low [11] The output speed is
lower than the setting in 4-52 Warning
Speed Low .
[12] Above speed
high
Above speed high [12] The output speed is
higher than the setting in 4-53 Warning
Speed High .
[13] Out of feedb.
range
Out of feedb. Range [13] The feedback is
outside the range set in 4-56 Warning
Feedback Low and 4-57 Warning Feedback
High .
[14] Below feedb. low Below feedb. Low [14] The feedback is
below the limit set in 4-56 Warning
Feedback Low .
[15] Above feedb.
high
Above feedb. High [15] The feedback is
above the limit set in 4-57 Warning
Feedback High .
[16] Thermal warning Thermal warning [16] The thermal warning
turns on when the temperature exceeds
the limit in the motor, the frequency
converter, the brake resistor or the
thermistor.
[17] Mains out of
range
Mains out of range [17] The mains voltage
is outside the specified voltage range.
[18] Reversing Reversing [18] The output is high when
the frequency converter is running
counter clockwise (the logical product of
the status bits “running” AND “reverse”).
[19] Warning Warning [19] A warning is active.
[20] Alarm (trip) Alarm (trip) [20] A (trip) alarm is active.
[21] Alarm (trip lock) Alarm (trip lock) [21] A (Trip lock) alarm is
active.
[22] Comparator 0 Comparator 0 [22] Use the result of
comparator 0.
13-01 Start Event
Option: Function:
[23] Comparator 1 Comparator 1 [23] Use the result of
comparator 1.
[24] Comparator 2 Comparator 2 [24] Use the result of
comparator 2.
[25] Comparator 3 Comparator 3 [25] Use the result of
comparator 3.
[26] Logic rule 0 Logic rule 0 [26] Use the result of logic rule
0.
[27] Logic rule 1 Logic rule 1 [27] Use the result of logic rule
1.
[28] Logic rule 2 Logic rule 2 [28] Use the result of logic rule
2.
[29] Logic rule 3 Logic rule 3 [29] Use the result of logic rule
3.
[33] Digital input DI18 Digital input DI18 [33] Use the result of
digital input 18.
[34] Digital input DI19 Digital input DI19 [34] Use the result of
digital input 19.
[35] Digital input DI27 Digital input DI27 [35] Use the result of
digital input 27.
[36] Digital input DI29 Digital input DI27 [35] Use the result of
digital input 29.
[37] Digital input DI32 Digital input DI32 [37] Use the result of
digital input 32.
[38] Digital input DI33 Digital input DI33 [38] Use the result of
digital input 33.
[39] Start command Start command [39] A start command is
issued.
[40] Drive stopped Drive stopped [40] A stop command ( Jog,
Stop, Qstop, Coast) is issued – and not
from the SLC itself.
[41] Reset Trip Reset Trip [41] A reset is issued
[42] Auto-reset Trip Auto-reset Trip [42] An Auto reset is
performed.
[43] Ok key OK key [43] The [OK] key is pressed.
[44] Reset key Reset key [44] The [Reset] key is pressed.
[45] Left key
Left key [45] The [
◄
] key is pressed.
[46] Right key Right key [46] The[
►
] key is pressed.
[47] Up key
Up key [47] The [
▲
] key is pressed.
[48] Down key
Down key [48] The [
▼
] key is pressed.
[50] Comparator 4 Comparator 4 [50] Use the result of
comparator 4.
[51] Comparator 5 Comparator 5 [51] Use the result of
comparator 5.
Parameter Descriptions FC 300 Programming Guide
126 MG.33.MB.02 - VLT
®
is a registered Danfoss trademark
3 3