manualshive.com logo in svg

Danfoss MCB 113, Руководство по эксплуатации, Страница: 24 / 54

Поделиться
Скачать
Danfoss MCB 113 Скачать руководство пользователя страница 24

Option

Function

[109]

Enable Vir.Mas-
ter

NOTICE

This option is available only with IMC software version 48.XX.

Enable signal for the virtual master function. Only applicable when option 

[10] Synchronization

 is selec-

ted in 

parameter 1-00 Configuration Mode

.

[110]

Start homing

NOTICE

This option is available only with IMC software version 48.XX.

Starts the homing function selected in 

parameter 17-80 Homing Function

. Must remain high until homing

is done, otherwise homing is aborted.

[111]

Activate touch

NOTICE

This option is available only with IMC software version 48.XX.

Activates the monitoring of the touch sensor input.

[112]

Relative posi-
tion

NOTICE

This option is available only with IMC software version 48.XX.

This option selects between absolute and relative positioning. The option is valid for the next position-
ing command.

[113]

Enable refer-
ence

NOTICE

This option is available only with IMC software version 48.XX.

Positioning mode: The drive activates the selected positioning type and target and starts the motion to-
wards the new target. The motion starts either immediately or when active positioning is completed, de-
pending on settings of 

parameter 17-90 Absolute Position Mode

 and 

parameter 17-91 Relative Position

Mode

. Synchronization mode: High signal locks the actual follower position to the actual master position.

The follower starts and catches up with the master. Low signal stops the synchronization and the follow-
er makes a controlled stop.

[114]

Sync. to Pos.
Mode

NOTICE

This option is available only with IMC software version 48.XX.

Select positioning in synchronization mode.

Parameter Setup

Operating Guide  | VLT® Extended Relay Card MCB 113

AQ322553864968en-000101 / 130R0353

24 | Danfoss A/S © 2020.01

Содержание MCB 113























































Отзывы:

Нет отзывов