Danfoss MCA 123 POWERLINK Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 53

Danfoss MCA 123 POWERLINK Скачать руководство пользователя страница 49

Bit
no.

Description Value=[

0]

Value=[1]

Comment

30

Reserved

Value shall be
read as 0

31

Reserved

Value shall be
read as 0

Table 9.3 POWERLINK Bits

9.1.3 Warning 34 Appears even though

Communication is Established

If the master is in stop mode, Warning 34 appears. Check
that the master is in run mode. If the frequency converter
is not in operational state Warning 34 will appear (60 s
after power up or immediately if the frequency converter
has been in operational state).

9.1.4 Frequency Converter Does Not

Respond to Control Signals

Check 1: Is the Control word valid?
If bit 10=0 in the Control word, the frequency converter
does not accept the Control word.

Check 2: Is the relationship between bits in the Control
word and the terminal I/Os correct?
Check the logical relationship in the frequency converter.

Define the desired logical relationship in

8-50 Coasting

Select

to

8-56 Preset Reference Select

according to the

following range of options. Select the FC control mode,
digital input and/or serial communication, using

8-50 Coasting Select

to

8-56 Preset Reference Select

.

If

8-01 Control Site

is set to digital only, then the frequency

converter will not react on commands send via the control
word.

Table 9.4

to

Table 9.11

show a coast command's effect

upon the frequency converter for the full range of

8-50 Coasting Select

settings.

The effect of control mode upon the function of

8-50 Coasting Select

,

8-51 Quick Stop Select

, and

8-52 DC

Brake Select

is as follows:

If

[0] Digital input

is selected, the terminals control the

Coast and DC Brake functions.

NOTE

Coasting, Quick Stop, and DC brake functions are active for
logic 0.

Terminal

Bit 02/03/04

Function

0

0

Coast/DC brake/Q-Stop

0

1

Coast/DC brake/Q-Stop

1

0

No Coast/DC brake/Q-Stop

1

1

No Coast/DC brake/Q-Stop

Table 9.4 [0] Digital Input

If

[1] Serial communication

is selected, commands are

activated only when given via serial communication.

Terminal

Bit 02/03/04

Function

0

0

Coast/DC brake/Q-Stop

0

1

No Coast/DC brake/Q-Stop

1

0

Coast/DC brake/Q-Stop

1

1

No Coast/DC brake/Q-Stop

Table 9.5 [1] Serial Communication

If

[2] Logic AND

is selected, both signals must be activated

to perform the function.

Terminal

Bit 02/03/04

Function

0

0

Coast/DC brake/Q-Stop

0

1

No Coast/DC brake/Q-Stop

1

0

No Coast/DC brake/Q-Stop

1

1

No Coast/DC brake/Q-Stop

Table 9.6 [2] Logic AND

If

[3] Logic OR

is selected, activation of one signal activates

the function.

Terminal

Bit 02/03/04

Function

0

0

Coast/DC brake/Q-Stop

0

1

Coast/DC brake/Q-Stop

1

0

Coast/DC brake/Q-Stop

1

1

No Coast/DC brake/Q-Stop

Table 9.7 [3] Logic OR

The effect of control mode upon the function of

8-53 Start

Select

and

8-54 Reversing Select

:

If

[0] Digital input

is selected, the terminals control the start

and reversing functions

Terminal

Bit 06/15

Function

0

0

Stop/Anti-clockwise

0

1

Stop/Anti-clockwise

1

0

Start/Clockwise

1

1

Start/Clockwise

Table 9.8 [0] Digital input

Troubleshooting

MCA 123 POWERLINK Operating Instructions

MG92C102 - VLT

®

is a registered Danfoss trademark

47

9

9

«
...
47
48
49
50
51
...
»

Содержание MCA 123 POWERLINK






















































Отзывы:

Нет отзывов