Dalsa BOA2-XAX-INS Скачать руководство пользователя страница 8

Страница: 8 / 36

Installation

This section details how to connect the BOA2 vision system with its associated
components and factory environment.

Definitions

Designator

LAN

10/100/1000 BaseT Ethernet connection. Provides the primary interface for
configuring the camera, developing the application and monitoring results.

I/O PWR

Provides access to the camera I/O – 3 IN, 3 OUT, RS232. Also provides
PWR input (12-30V).

LAMP

Provides PWR and strobe control to a local LED light source.

NOTE: Lamp

PWR is identical to BOA2 PWR input (24V).

LAN LED

Red/Green/Yellow = Network activity
Blue = Warm Reset

LED1

Blue = Camera booted, not configured (no Solution file)
Green = Solution loaded, ready to run, or acquisition in progress.
Red = Camera Fault

LED2

Connecting the BOA2 Vision System

Camera Connectors and Indicators

Blue blink = Booting (should stop after 20 seconds). In a few releases LED2

continued to blink until the first trigger if a solution that requires a trigger
is auto-loaded at boot. Fixed in release 2006.

Green = Inspection Pass (runtime)
Blue = Inspection Recycle (runtime);
Red = Inspection Fail (runtime)
Off = Waiting for trigger (runtime)

Version 4.3; 2017-11-20

BOA2-XA Installation

Содержание BOA2-XAX-INS





































Результаты поиска

Содержание BOA2-XAX-INS

Отзывы:

Похожие инструкции для BOA2-XAX-INS

Бренды по названию

Популярные бренды

Dalsa BOA2-XAX-INS, Руководство по установке

Результаты поиска

Содержание BOA2-XAX-INS

Отзывы:

Похожие инструкции для BOA2-XAX-INS

Бренды по названию

Популярные бренды